sodcalculator

10 Tech How-To

Overdraft vs Credit Card: Key Differences

Tag 10-56447 · Updated · Standard formula, shown below

Volume 9.26 yd³
Volume
250.0 ft³
Result
Lawn length
40 ft
You entered
Lawn width
25 ft
You entered
You enter
Lawn length, Lawn width, Depth
You get
Volume, Volume
Rounding
2 dp · 1 dp

An overdraft is a short-term loan attached to your checking account that covers transactions when your balance falls below zero, while a credit card is a revolving line of credit that lets you borrow up to a set limit for purchases anywhere cards are accepted. The core difference is where the borrowing happens: overdrafts extend your bank account, credit cards are a separate payment tool. Both charge interest and fees, but they work in very different ways, and choosing between them depends on how you plan to borrow and repay.

Formula

The calculator above computes the volume of soil, mulch, or other material needed to cover a rectangular lawn to a given depth. The formula is:

Volume (yd³) = Length (ft) × Width (ft) × Depth (in) ÷ 324

Where:

  • Length – lawn length in feet
  • Width – lawn width in feet
  • Depth – desired coverage depth in inches
  • 324 – conversion factor (1 cubic yard = 27 cubic feet; 1 foot = 12 inches, so 27 × 12 = 324)

The second output gives the volume in cubic feet, using the formula Length × Width × Depth ÷ 12 (since depth is in inches, dividing by 12 converts it to feet).

Worked Example

Using the default values: length = 40 ft, width = 25 ft, depth = 3 in.

  1. Calculate the volume in cubic feet: 40 × 25 × 3 ÷ 12 = 3000 ÷ 12 = 250 ft³
  2. Convert to cubic yards: 250 ÷ 27 = 9.259 yd³ (rounded to 2 decimals: 9.26 yd³)

So you need about 9.26 cubic yards of material to cover a 40×25 ft lawn at 3 inches deep. The calculator shows the same result.

When to Use This Calculator

Use this calculator when planning to add a layer of topsoil, compost, sand, or mulch to a lawn or garden bed. It helps you estimate how much material to order, which is typically sold by the cubic yard (bulk) or by the cubic foot (bagged). For bulk orders, you usually round up to the nearest whole cubic yard. For bagged products, check the bag volume (often 1–2 cubic feet) and divide your total cubic feet by that number.

How to Read the Result

The first number is the volume in cubic yards – the standard unit for bulk deliveries. The second is in cubic feet, which is useful if you’re buying bags. If your result is 9.26 yd³, you would order 10 cubic yards from a bulk supplier (since they don’t deliver partial yards). If buying 2-cubic-foot bags, you’d need 250 ÷ 2 = 125 bags.

Common Mistakes

  • Mixing units: Depth is in inches, but length and width are in feet. The formula handles this, but if you enter depth in feet, the result will be wrong.
  • Forgetting to round up: For bulk orders, always round up to the next whole yard – you can’t order 9.26 yards.
  • Ignoring compaction: Some materials settle after spreading. For loose fill like compost, consider adding 10–15% extra.

Limitations

This formula assumes a perfectly rectangular area with uniform depth. Real lawns have curves, slopes, and irregular shapes – for those, break the area into rectangles and add the volumes, or use a more precise survey. Also, the calculator does not account for material loss during spreading, so it’s wise to order slightly more than the calculated amount.

Frequently Asked Questions

How many cubic feet are in a cubic yard?

There are 27 cubic feet in one cubic yard (3 feet × 3 feet × 3 feet). This is why the conversion factor 324 appears: 27 × 12 (to convert inches to feet) = 324.

Should I order in cubic yards or cubic feet?

Bulk suppliers sell by the cubic yard, which is usually cheaper for large areas. Bagged products are sold by cubic foot, convenient for small projects but more expensive per volume. Use the cubic yard output for bulk, the cubic feet output for bags.

How deep should I spread topsoil on an existing lawn?

For a light topdressing to level minor dips, ¼ to ½ inch is enough. For a new lawn bed, 4–6 inches is typical. This calculator lets you adjust depth to see how volume changes.

What if my lawn isn’t a perfect rectangle?

Divide the area into rectangles, calculate each with this calculator, and add the volumes. For triangular or circular sections, use appropriate area formulas first (area × depth = volume).

Does the calculator work for mulch or gravel?

Yes, the math is the same for any bulk material. Just be aware that different materials have different weights per cubic yard, so if you’re paying by weight, you’ll need the density.

Related

Formula used
in l | Lawn length | ft | 40 | 0 | 100000
in w | Lawn width | ft | 25 | 0 | 100000
in d | Depth | in | 3 | 0 | 120
out yd | Volume | yd³ | l * w * d / 324 | 2
out ft3 | Volume | ft³ | l * w * d / 12 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More in this bed

The whole Tech How-To bed →