The F24 error code on a Kenmore washer indicates a communication failure between the main control board and the motor control board (or inverter). This typically means the washer cannot properly communicate with its motor, causing the cycle to stop and the code to display. Below, we explain what triggers this error, how to diagnose it, and the steps you can take to resolve it.
What the F24 Code Means
Kenmore washers, particularly front-load and some high-efficiency top-load models made by LG, use a network of electronic boards to manage the motor, sensors, and user interface. The F24 code is a generic communication error: the main control board (the one behind the control panel) is not receiving a valid response from the motor control board (the one attached to the motor). This can happen at any point during a cycle, but it often appears during the spin or drain phase when the motor is under load.
It is important to distinguish F24 from other codes. For example, F21 indicates a drainage problem, and F23 is a motor tachometer error. F24 specifically points to a wiring or board communication issue, not a mechanical blockage.
Common Causes of F24
The most frequent causes, in order of likelihood, are:
- Loose or damaged wiring harness – The connectors between the main control board and the motor control board can vibrate loose over time, or the wires can chafe and break.
- Failed motor control board – This board, often called the inverter, can fail due to power surges, overheating, or moisture.
- Failed main control board – Less common, but the main board can also fail, preventing communication.
- Faulty motor – In rare cases, the motor itself has a short or open winding, which the motor control board detects as a communication failure.
- Software glitch – A temporary firmware error can sometimes cause a false F24.
Diagnostic Steps Before Calling a Technician
Before you replace any parts, try these steps in order. They are safe and require no special tools.
- Reset the washer: Unplug the washer from the power outlet (or turn off the circuit breaker) for 1–5 minutes. Then plug it back in and run a short cycle. This clears temporary glitches.
- Check the door latch: A loose or faulty door lock can sometimes cause communication errors. Open and close the door firmly, and ensure the latch clicks.
- Inspect the wiring harness: Unplug the washer, remove the top or rear panel (depending on model), and visually inspect the connectors between the main control board and the motor control board. Look for loose pins, burnt smells, or broken wires. Re-seat any loose connectors.
- Test with a multimeter: If you have a multimeter, you can check continuity on the wiring harness. This requires a wiring diagram, which is usually on a sticker inside the cabinet. If you are not comfortable with electrical testing, skip this.
- Run a diagnostic mode: Many Kenmore/LG washers have a built-in diagnostic test. To enter it, press and hold the “Spin” and “Soil” buttons simultaneously for 3 seconds (or as per your model’s manual). This will run a series of tests and may display a different code that pinpoints the issue.
How to Fix the F24 Error
Once you have identified the likely cause, here are the fixes:
- Re-seat connectors: Simply unplugging and re-plugging the harness connectors often solves intermittent issues. Use a small flathead screwdriver to gently pry up any locking tabs.
- Replace the motor control board: If the wiring is intact and the reset doesn’t help, the motor control board is the most likely culprit. You can order a replacement part online or from a local appliance parts store. It is usually located at the bottom rear of the washer, attached to the motor. Disconnect power, remove the panel, unplug the board, and install the new one.
- Replace the main control board: If the motor control board is fine, the main board may be faulty. This is a more expensive part and is located behind the control panel. It is often worth having a professional diagnose this, as the main board is not returnable in many cases.
- Replace the motor: If the motor windings are shorted, the motor itself must be replaced. This is a heavy, expensive part and usually requires professional installation.
Cost Considerations
Repair costs vary widely. A DIY fix by re-seating connectors is free. A motor control board can cost between $80 and $200 for the part, while a main control board can range from $150 to $300. A motor can cost $200 or more. Professional labor adds $100–$200 per visit. If your washer is older than 7–10 years and the repair is over $400, it may be more economical to replace the washer.
How to Prevent F24 in the Future
- Use a surge protector: Power surges can damage control boards. Plug the washer into a dedicated surge protector.
- Keep the washer level: Excessive vibration can loosen wiring. Ensure the washer is level and the lock nuts on the legs are tight.
- Clean the lint filter: A clogged filter can cause the motor to overwork, leading to overheating and board failure.
- Don’t overload: Overloading stresses the motor and can cause premature failure.
Frequently Asked Questions
Can I still use my washer if it shows F24?
No. The washer will not operate when F24 is displayed because the control board cannot communicate with the motor. Continuing to try may cause further damage. You must address the error before using the washer.
Is F24 the same as a drain problem?
No. F24 is a communication error, not a drain issue. A drain problem usually triggers F21 or a different code. However, if the washer stops mid-drain, you might see F24 because the motor cannot spin to pump water out. Check for clogs in the drain hose or pump filter first if you suspect a drain issue.
How do I reset my Kenmore washer to clear F24?
Unplug the washer for 1–5 minutes, then plug it back in. This resets the control boards. If the code returns immediately, the issue is hardware-related, not a glitch.
Where is the motor control board located?
On most Kenmore/LG washers, the motor control board is attached to the bottom of the motor, accessible by removing the rear or bottom panel. It is a small circuit board with several wires connected to it.
Should I replace the main control board first?
No. The motor control board is more likely to fail than the main board. Start with the cheaper and easier fixes: reset, wiring inspection, and then the motor control board. Only replace the main board after confirming the motor control board is working.
Can a faulty door latch cause F24?
Yes, in some cases. If the door latch does not send a locked signal, the main board may not start the motor, and a communication error can occur. Check the door latch for debris or damage and replace it if needed.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Show User Library in macOS High Sierra & Sierra
- Device Manager Shortcut: Windows 10 Desktop
- How to Remove Forgotten Passcode from iPhone
- Fix Slow Wi-Fi Problem iPhone X: 9 Steps
- How to Check if a Candidate Accepts Crypto Donations
- How to Listen to Deleted Voicemails on iPhone