sodcalculator

10 Tech How-To

Fix DHCP Not Enabled for Wi-Fi in Windows 11

Guide 10-43224 · Updated · Step by step

If Windows 11 says “DHCP is not enabled for Wi-Fi,” your network adapter is set to a static IP address, and the fix is to switch it back to automatic (DHCP) in the adapter’s IPv4 properties. This usually takes less than a minute and resolves the “No internet access” or “Unidentified network” error. Below is the full step-by-step fix, plus what DHCP does, why it gets disabled, and what to do if the standard fix doesn’t work.

What Does “DHCP Not Enabled” Mean?

DHCP (Dynamic Host Configuration Protocol) is the system that automatically assigns your computer an IP address, subnet mask, default gateway, and DNS servers when you connect to a network. When DHCP is enabled, your PC “asks” the router for these settings each time it connects. When DHCP is disabled, your PC uses a static (manually entered) IP address instead.

If that static IP is wrong, outdated, or conflicts with another device, Windows can’t communicate with the network properly. The error “DHCP is not enabled for Wi-Fi” appears in the Network Diagnostics tool, but the underlying issue is that your Wi-Fi adapter is configured to use a fixed IP that isn’t valid for the current network.

How to Fix DHCP Not Enabled for Wi-Fi in Windows 11

Follow these steps to re-enable DHCP on your Wi-Fi adapter:

  1. Press Windows + R, type ncpa.cpl, and press Enter. This opens the Network Connections window.
  2. Right-click your Wi-Fi adapter (it may be labeled “Wi-Fi” or “Wireless Network Connection”) and select Properties.
  3. In the list, scroll down to Internet Protocol Version 4 (TCP/IPv4) and double-click it (or select it and click Properties).
  4. Select Obtain an IP address automatically and Obtain DNS server address automatically.
  5. Click OK on both windows.
  6. Restart your Wi-Fi connection by turning Wi-Fi off and on again, or restart your PC.

If you also see a similar option for IPv6, you can leave it as is, but for most home networks IPv4 is what matters.

Why Did DHCP Get Disabled in the First Place?

There are a few common reasons why your Wi-Fi adapter ends up with a static IP:

  • Manual configuration: Someone (or you) previously set a static IP for a specific network, and it was never changed back.
  • Third-party VPN software: Some VPN clients or network management tools change adapter settings and don’t restore them.
  • Malware or misconfiguration: Rarely, malware or a misbehaving driver can alter network settings.
  • Windows update glitch: Occasionally a Windows update can reset network settings in unexpected ways, though this is less common.

Once you switch back to automatic, the error should disappear. If it comes back after a reboot, you may need to check for third-party software that is forcing a static IP.

What to Do If the Standard Fix Doesn’t Work

If you’ve set the adapter to obtain an IP automatically but still see the error, try these additional steps in order:

  1. Release and renew your IP: Open Command Prompt as administrator and run ipconfig /release followed by ipconfig /renew.
  2. Flush DNS: In the same Command Prompt, run ipconfig /flushdns.
  3. Reset the network stack: Run netsh winsock reset and netsh int ip reset, then restart your PC.
  4. Restart your router: Unplug your router for 30 seconds and plug it back in. This can fix issues where the router’s DHCP server is stuck.
  5. Update your Wi-Fi driver: Go to Device Manager, expand “Network adapters,” right-click your Wi-Fi adapter, and select “Update driver.” Choose “Search automatically for drivers.”
  6. Disable and re-enable the adapter: In Device Manager, right-click the adapter and select “Disable,” then right-click again and select “Enable.”

If none of these work, try connecting to a different network (like a mobile hotspot) to see if the issue is with your Wi-Fi adapter or your router. If the error only happens on one network, the problem is likely on the router side.

How to Check Your Current IP Configuration

To see whether your PC is using DHCP or a static IP, open Command Prompt and run ipconfig /all. Look for the line “DHCP Enabled” under your Wi-Fi adapter. If it says “No,” then DHCP is off. If it says “Yes,” then DHCP is on, and the problem may be elsewhere.

You can also check the IPv4 address. If it starts with 169.254, that means Windows couldn’t get an IP from the router and assigned itself an Automatic Private IP Address (APIPA). That usually indicates a DHCP server problem on the router, not a configuration issue on your PC.

Common Misconceptions About DHCP and Static IPs

One common misconception is that a static IP is always better for gaming or streaming. In reality, for most home users, DHCP is perfectly fine and much easier to manage. Static IPs are useful for printers, servers, or port forwarding, but they require careful configuration. If you set a static IP that’s outside your router’s DHCP range, or you mistype the subnet mask or gateway, you’ll lose connectivity exactly like this error describes.

Another misconception is that the “DHCP not enabled” error means your router is broken. It usually doesn’t. It means your PC’s network adapter is set to manual mode. The fix is almost always on the PC side.

Frequently Asked Questions

Why does my Wi-Fi say “DHCP is not enabled” when I try to troubleshoot?

Windows runs a diagnostic that checks whether your network adapter is set to obtain an IP automatically. If it finds that the adapter is configured with a static IP, it reports “DHCP is not enabled.” The fix is to go into the adapter’s IPv4 properties and select “Obtain an IP address automatically.”

Can I fix DHCP not enabled without admin rights?

No. Changing network adapter settings requires administrator privileges. If you’re on a work or school computer, you may need to contact your IT department. On your own PC, you should have admin rights by default, but if not, you’ll need to log in with an administrator account.

Will resetting Windows fix the DHCP issue?

Resetting Windows (or using “Network reset” in Settings) will restore all network adapters to their default settings, which includes enabling DHCP. However, it’s a heavy solution. Try the manual steps first; they are faster and less disruptive. Network reset also removes all saved Wi-Fi passwords and VPN connections.

Is it safe to use a static IP instead of DHCP?

Yes, it’s safe if you know what you’re doing. You need to pick an IP address that is not in the router’s DHCP range, and you must enter the correct subnet mask (usually 255.255.255.0) and default gateway (your router’s IP). But for most users, DHCP is simpler and less error-prone.

Why does my DHCP keep turning off after I fix it?

If DHCP keeps reverting to static, something is changing the adapter settings. This could be a third-party network management tool, a VPN client, or a corrupted driver. Try updating the driver, and check if any software you installed recently is modifying network settings. You can also run a full malware scan.

Does this fix work for Ethernet too?

Yes, the same steps work for an Ethernet adapter. If you get a similar DHCP error on a wired connection, just right-click your Ethernet adapter instead of Wi-Fi in the Network Connections window.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →