sodcalculator

10 Tech How-To

Fix USB Ports Not Working in Windows 10

Guide 10-57857 · Updated · Step by step

If your USB ports have stopped working in Windows 10, the fix is usually a quick driver reset, a power management tweak, or a check of the physical port itself. Start by restarting your PC, then unplugging the device and plugging it into a different port; if that fails, follow the step-by-step driver and power settings fixes below.

Why USB Ports Stop Working

USB ports in Windows 10 can fail for several distinct reasons, and knowing which one applies to you shortens the repair time. The most common causes are:

  • Driver corruption or outdated drivers – Windows updates or third-party software can break the USB controller driver.
  • Selective suspend power saving – Windows may cut power to a port to save battery, and sometimes it doesn’t wake it back up.
  • Fast Startup interference – The hybrid shutdown feature can leave USB controllers in a bad state.
  • Physical damage or debris – Bent pins, dust, or a broken port are common, especially on laptops.
  • BIOS/UEFI settings – Legacy USB support or XHCI hand-off can be disabled or misconfigured.
  • Electrical surge or short circuit – A faulty device can trigger Windows to disable the port to protect the motherboard.

Before you start changing settings, do a quick hardware check. Try the USB device on another computer. If it works there, the problem is your PC. If it doesn’t, the device or cable is at fault – replace the cable first, as they fail far more often than ports.

Quick Fixes to Try First

These take under a minute each and resolve a surprising number of cases:

  1. Restart your computer – A full shutdown and boot clears transient driver states. Use Start > Power > Restart, not Shut Down (Fast Startup can persist the problem).
  2. Unplug the device and wait 10 seconds, then plug it into a different USB port. If it works in another port, the original port may be physically damaged.
  3. Check for debris – Look inside the port with a flashlight. Compressed air or a wooden toothpick can dislodge dust. Never use metal tools while the PC is on.
  4. Try a different cable – USB cables, especially cheap ones, break internally without visible damage.
  5. Connect the device directly to the motherboard – If you’re on a desktop, avoid front-panel ports and hubs; they sometimes don’t supply enough power.

If none of these work, move on to the software fixes below, which address the majority of remaining cases.

Fix 1: Reinstall or Update the USB Controller Driver

This is the single most effective fix for Windows 10 USB issues. The driver controls how Windows talks to the USB hardware, and a corrupted or outdated version causes ports to ignore devices entirely.

  1. Press Windows + X and select Device Manager.
  2. Expand Universal Serial Bus controllers.
  3. Look for entries with a yellow warning icon, or any named USB Root Hub or Host Controller.
  4. Right-click each one and select Uninstall device. Check the box that says Delete the driver software for this device if it appears.
  5. Restart your PC. Windows will automatically reinstall the correct drivers.

If Windows doesn’t reinstall automatically, go to your PC manufacturer’s support website (Dell, HP, Lenovo, etc.) and download the latest chipset or USB driver for your exact model. Installing the manufacturer’s driver over the generic Microsoft one often fixes stubborn issues.

For a deeper clean, you can also run Windows Update (Settings > Update & Security > Windows Update) and install any optional driver updates. Microsoft pushes USB controller updates through this channel regularly.

Fix 2: Disable USB Selective Suspend

Windows 10 has a power-saving feature that puts individual USB ports to sleep when they’re idle. It’s designed for laptops, but it can fail to wake the port, especially with external drives, keyboards, or mice.

  1. Open Control Panel (search for it in the Start menu).
  2. Go to Hardware and Sound > Power Options.
  3. Next to your selected plan, click Change plan settings.
  4. Click Change advanced power settings.
  5. Scroll to USB settings and expand it.
  6. Expand USB selective suspend setting and set both On battery and Plugged in to Disabled.
  7. Click Apply and OK, then restart.

This disables the feature entirely, which slightly increases power draw on laptops but eliminates the most common cause of intermittent USB failures.

Fix 3: Turn Off Fast Startup

Fast Startup is a Windows 10 feature that saves a kernel image to disk on shutdown, making boot faster. The downside is that it can leave USB controllers in a half-initialized state, causing ports to not respond after boot.

  1. Open Control Panel > Hardware and Sound > Power Options.
  2. Click Choose what the power buttons do on the left.
  3. Click Change settings that are currently unavailable (requires admin rights).
  4. Uncheck Turn on fast startup (recommended).
  5. Click Save changes and restart.

If your USB ports work after this, you can leave Fast Startup off permanently. The boot time difference is usually only a few seconds on modern SSDs.

Fix 4: Check Power Management Settings on USB Hubs

Even with selective suspend disabled, individual USB hubs can have a separate power management setting that allows Windows to turn them off.

  1. Open Device Manager again.
  2. Expand Universal Serial Bus controllers.
  3. Right-click each USB Root Hub and select Properties.
  4. Go to the Power Management tab.
  5. Uncheck Allow the computer to turn off this device to save power.
  6. Repeat for every hub listed, then restart.

This is a separate setting from selective suspend, and it’s easy to miss. Do this for all hubs, not just the one you think is failing.

Fix 5: Use the Hardware and Devices Troubleshooter

Windows 10 includes a built-in troubleshooter that can detect and fix common USB problems automatically. It’s not always sufficient, but it’s worth running before more invasive steps.

  1. Open Settings (Windows + I).
  2. Go to Update & Security > Troubleshoot > Additional troubleshooters.
  3. Select Hardware and Devices and click Run the troubleshooter.
  4. Follow the prompts. It may ask you to plug in the problematic device.

This tool checks for driver issues, power problems, and hardware conflicts. It won’t fix physical damage, but it can resolve software conflicts you didn’t know existed.

Fix 6: Update BIOS/UEFI and Reset USB Settings

If all software fixes fail, the problem may be in your motherboard’s firmware. BIOS updates often include USB controller fixes, and resetting the settings can clear corrupted configuration data.

  1. Check your motherboard or laptop manufacturer’s website for a BIOS update. Follow their instructions exactly – a failed BIOS update can brick the system.
  2. Alternatively, enter BIOS (usually by pressing Del, F2, or F10 during boot) and look for USB settings. Enable Legacy USB Support and XHCI Hand-off if they exist.
  3. If you’ve made changes, save and exit. If not, try Load Optimized Defaults and reboot.

Only update BIOS if you’re comfortable with the process. For most users, the driver and power management fixes above resolve the issue without touching firmware.

When It’s a Hardware Problem

If you’ve tried all the software fixes and USB still doesn’t work, the port itself may be dead. Here’s how to tell:

  • All ports fail – Likely the motherboard’s USB controller or the chipset. This can be a hardware failure or a BIOS issue.
  • One port fails – Usually physical damage. Bent pins, cracked solder joints, or debris.
  • Port works sometimes – Could be a loose connection or a failing cable. Try a different device in that port.
  • Device is recognized but doesn’t work – Check the device’s own drivers and power supply. Some external drives need more power than a single port provides.

For desktops, you can add a PCIe USB expansion card for under $20. For laptops, a USB-C or USB-A hub is the practical workaround. If the motherboard is under warranty, contact the manufacturer before opening anything.

Frequently Asked Questions

Why does my USB port work in BIOS but not in Windows?

This points to a Windows driver or power management issue, not a hardware failure. The BIOS uses its own minimal USB driver, so if it works there, the port is physically fine. Run the Device Manager uninstall/reinstall steps and disable selective suspend – one of those will almost always fix it.

Can a USB port be repaired?

Yes, but it depends on the damage. Loose solder joints can be reflowed by a technician, and bent pins can sometimes be straightened. However, on modern laptops the USB ports are often soldered directly to the motherboard, making repair cost more than a replacement. For desktops, the motherboard’s USB headers can be replaced with a front-panel hub or a PCIe card.

Why does my USB device work on another computer but not mine?

Your computer’s USB port may not be providing enough power, or the port’s data pins are damaged. Try a different port on your PC first. If none work, the issue is likely the driver or power settings – follow the selective suspend and Device Manager fixes. If those fail, test with a powered USB hub to rule out power delivery.

How do I know if my USB port is dead or just disabled?

Open Device Manager and look under Universal Serial Bus controllers. If you see a grey arrow or a yellow warning icon, the port is disabled or has a driver problem. Right-click and select Enable device if it’s disabled. If it’s not listed at all, the port may be physically dead or not detected by Windows.

Will a Windows update fix my USB ports?

Sometimes. Microsoft regularly includes USB controller driver updates in cumulative updates. Check Windows Update for optional driver updates, and also check your PC manufacturer’s support site for a chipset driver. If the issue started after a recent update, you can roll back the driver in Device Manager (right-click the USB controller > Properties > Driver tab > Roll Back Driver).

Is it safe to uninstall USB controllers in Device Manager?

Yes, it’s safe. Windows will reinstall the drivers automatically on the next reboot. Uninstalling a USB controller only removes the software interface, not the hardware. Your data on USB drives is not affected. Just make sure you don’t uninstall the driver for your system drive if it’s an external USB boot drive – that could prevent booting.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →