If your iPhone won’t turn on, the fix is usually a forced restart, a charge, or a recovery mode restore, and this guide walks through each step in order. Start with the simplest fix—a forced restart—because it resolves a frozen or black screen in most cases without erasing any data. If that doesn’t work, the problem is likely a drained battery, a failed software update, or a hardware issue, and the steps below cover how to diagnose each one.
Why an iPhone Won’t Turn On
An iPhone that appears completely dead usually falls into one of four categories:
- Software freeze: The operating system has crashed and the screen is unresponsive, but the phone is still powered on.
- Drained battery: The battery is completely empty and needs to charge for several minutes before the phone will respond.
- Failed software update or restore: The phone is stuck in a recovery loop or on the Apple logo due to a corrupted update.
- Hardware failure: A damaged screen, battery, or internal component prevents the phone from powering up normally.
Knowing which category you’re in helps you choose the right fix. The steps below are ordered from least invasive to most invasive, so you don’t accidentally erase data when a simple restart would have worked.
Step 1: Force Restart Your iPhone
A forced restart is different from a normal restart. It bypasses the software shutdown process and directly reboots the hardware, which can clear a frozen state. The button sequence depends on your iPhone model:
- iPhone 8 or later (including SE 2nd gen and all Face ID models): Press and quickly release the Volume Up button, then press and quickly release the Volume Down button, then press and hold the Side button until the Apple logo appears. This can take up to 10 seconds.
- iPhone 7 and 7 Plus: Press and hold both the Side button and the Volume Down button simultaneously until the Apple logo appears.
- iPhone 6s and earlier (including SE 1st gen): Press and hold both the Home button and the Top (or Side) button simultaneously until the Apple logo appears.
If the Apple logo appears, your iPhone is working. If the screen stays black, move to the next step.
Step 2: Check the Charging Setup
A completely drained iPhone can take up to 30 minutes of charging before it shows any sign of life. Before assuming the battery is dead, verify your charging setup:
- Use the original Apple charging cable and a wall adapter. Low-power USB ports on computers or third-party chargers may not deliver enough current.
- Inspect the charging port for lint, dust, or debris. Use a soft, dry toothbrush or a wooden toothpick to gently clean it out. Never use metal objects.
- Try a different cable and a different wall adapter. Cables fray internally and stop working even if they look fine.
- If you have a wireless charger, try that as an alternative, but note that wireless charging is slower and may not work if the phone is completely dead.
After connecting to power, wait at least 15–30 minutes. If the screen remains black, try the forced restart again while the phone is plugged in. If you see a battery icon or a red battery indicator, the phone is charging and just needs time.
Step 3: Put the iPhone in Recovery Mode
If the phone still won’t turn on, it may be stuck in a software failure state. Recovery mode allows you to reinstall iOS without erasing your data, though a restore will erase everything if the update fails. Here’s how to enter it:
- Connect your iPhone to a computer with the latest version of iTunes (Windows) or Finder (macOS Catalina or later).
- Perform the forced restart sequence for your model, but this time do not release the buttons when the Apple logo appears. Keep holding until you see the Recovery Mode screen—a computer icon with a cable.
- On your computer, a dialog box will appear offering to Update or Restore. Choose Update first. This tries to reinstall iOS while keeping your files intact.
- If the update fails or the phone still doesn’t turn on, repeat the process and choose Restore. This erases the phone and installs a fresh copy of iOS.
Recovery mode is the most common fix for a phone that is stuck on the Apple logo or a black screen after a failed update. It requires a computer and a stable internet connection.
Step 4: Try DFU Mode (Last Software Resort)
Device Firmware Update (DFU) mode is a deeper restore that bypasses the bootloader entirely. It’s the final software step before hardware repair. Entering DFU mode is finicky and the screen stays completely black, so it’s easy to think you’ve failed. The exact sequence is model-specific, but generally:
- Connect the iPhone to your computer.
- For iPhone 8 or later: Press Volume Up, then Volume Down, then hold the Side button for 5 seconds. Then, while still holding the Side button, press and hold Volume Down for 10 seconds. Release the Side button but keep holding Volume Down for another 5 seconds. If the screen stays black and iTunes/Finder says it detected an iPhone in recovery mode, you’ve done it.
- For iPhone 7: Hold Side + Volume Down for 10 seconds, then release Side but keep holding Volume Down for 5 more seconds.
- For iPhone 6s and earlier: Hold Home + Top button for 10 seconds, then release Top but keep holding Home for 5 more seconds.
Once in DFU mode, iTunes/Finder will prompt you to Restore. This wipes the phone completely. If DFU mode doesn’t work, the issue is almost certainly hardware.
Common Misconception: The Screen vs. The Phone
A black screen doesn’t always mean the phone is off. If the phone vibrates, makes sounds, or responds to Siri when you call it, the logic board is working but the display or its connector is broken. Try these checks:
- Call the phone from another line. If it rings or vibrates, the screen is the problem, not the phone.
- Connect to a computer and see if it appears in Finder/iTunes. If it does, the phone is on.
- Try a forced restart even if you hear sounds—it can sometimes reinitialize a stuck display.
If the phone responds to calls but the screen is black, you need a screen replacement, not a software fix.
When to Seek Professional Repair
If none of the software fixes work and the phone doesn’t respond to charging or a computer, the problem is likely hardware. Common hardware failures include:
- Battery failure: A swollen or completely dead battery won’t hold a charge. This is the most common hardware issue on older iPhones.
- Charging port damage: Even if the port looks clean, internal pins can be bent or corroded.
- Logic board failure: Water damage or a drop can kill the main board. This is the most expensive repair.
Apple Stores and Apple Authorized Service Providers can run diagnostics. Third-party repair shops may be cheaper but may void any remaining warranty. If your iPhone is under warranty or AppleCare+, use Apple’s official service first.
Frequently Asked Questions
How long should I charge a dead iPhone before it turns on?
Leave it plugged in for at least 30 minutes. A completely drained battery needs to build up enough voltage to boot the system. If nothing appears after an hour, the battery or charging circuit is likely faulty.
Will a forced restart delete my data?
No. A forced restart is safe and does not erase any data. It simply reboots the hardware. Only a Restore in recovery mode or DFU mode erases the phone.
Why does my iPhone show the Apple logo but then go black?
This usually indicates a failed software update or a corrupted system file. The phone boots, fails to load iOS, and shuts down. Putting it in recovery mode and choosing Update is the best first step.
Can a dead battery cause a black screen even when plugged in?
Yes. If the battery is completely dead, it may take several minutes of charging before the phone can even display the charging icon. If it never shows anything, the battery may need replacement.
Is it safe to use a third-party charger to revive a dead iPhone?
Generally yes, but use a reputable brand with proper certification. Very cheap chargers may not provide enough power or may damage the battery. If the phone doesn’t respond to a third-party charger, try an original Apple charger before concluding the phone is broken.
What if my iPhone is water damaged and won’t turn on?
Do not charge it or plug it into a computer. Water and electricity can cause short circuits. Turn it off if possible, dry it with a cloth, and leave it in a dry, ventilated area for at least 48 hours. Then try a forced restart. If it still won’t turn on, professional repair is required.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- MacBook Trackpad Protection: A Complete Guide
- PlayStation Overheating: Causes & Fixes
- How to Remove or Insert a SIM Card in Your iPhone
- How to Send a Fax from Android or iOS
- Outlook Stuck on Loading Profile? Fix It
- How to Choose a Gaming Mini PC for Games and Display