sodcalculator

10 Tech How-To

Restore Pitted Chrome Sink Drain Surrounds

Guide 10-44754 · Updated · Step by step

To restore pitted chrome sink drain surrounds, you must first remove the rust and corrosion, then re-plate or coat the exposed metal, because the pitting is damage to the chrome layer itself. The most reliable DIY method is to sand the pits smooth, polish the surface, and apply a high-temperature chrome-look paint or a brush-on nickel/chrome plating kit. This article explains the full process, the tools you need, and why some methods work better than others.

Why Chrome Drain Surrounds Pit

Chrome plating on drain surrounds is a thin layer—typically 0.0002 to 0.001 inches—over a base metal, usually brass or zinc alloy. Pitting occurs when the chrome layer is scratched or chipped, exposing the base metal to moisture and oxygen. The base metal corrodes, and the corrosion products push up and flake off the surrounding chrome, creating small craters or pits. Hard water, abrasive cleaners, and acidic substances like lemon juice or vinegar accelerate this process by attacking the thin chrome layer.

Once pitting starts, it is a self-perpetuating cycle: each pit exposes more base metal, which corrodes further. You cannot simply polish out pits because the chrome layer is already gone in those spots. Polishing will only smooth the edges of the pit, leaving a dark crater. The only lasting fix is to either re-plate the area or apply a protective coating that fills the pits and seals the metal.

Tools and Materials You Will Need

For a DIY restoration, gather the following items, most of which are available at hardware stores or online:

  • Fine sandpaper or abrasive pads (400, 600, 800, 1000, and 2000 grit)
  • Rust remover or phosphoric acid-based metal prep solution
  • Metal polish (e.g., Brasso, Flitz, or Wenol)
  • Clean microfiber cloths
  • Painter’s tape and plastic sheeting to protect the sink
  • High-temperature chrome spray paint (rated for at least 200°F) or a brush-on chrome plating kit
  • Clear lacquer or automotive clear coat (optional, for extra protection)

If the pits are deep (more than 1/16 inch), you may need a metal filler like JB Weld to build up the surface before sanding. For severe pitting where the base metal is crumbling, replacement is often more practical than restoration.

Step-by-Step Restoration Process

  1. Clean the area: Remove the drain surround if possible (unscrew the top flange from below the sink). If not, tape off the surrounding sink surface with painter’s tape and plastic.
  2. Remove loose chrome and rust: Use a wire brush or 400-grit sandpaper to scrape away any flaking chrome and loose rust. Work gently to avoid enlarging the pits.
  3. Apply rust remover: Follow the product instructions to convert or dissolve remaining rust. Phosphoric acid-based removers leave a clean, slightly etched surface that helps paint adhere.
  4. Sand the pits smooth: Start with 400-grit, then progress to 600, 800, 1000, and finally 2000-grit, always sanding in a circular motion. The goal is to feather the edges of each pit and create a smooth, slightly matte surface. If pits are deep, fill them with metal epoxy first, let it cure, then sand flush.
  5. Polish the surface: Use a metal polish on a clean cloth to bring up a shine on the remaining chrome. Wipe off all residue with a clean cloth.
  6. Apply the coating: For spray paint, shake the can thoroughly and apply 3-4 thin coats, waiting 10-15 minutes between coats. For a brush-on plating kit, follow the kit’s instructions (usually involves applying a nickel solution and then a chrome top coat).
  7. Let it cure: Allow the coating to dry and cure fully, typically 24-48 hours, before using the sink.
  8. Reinstall the surround: Once cured, carefully remove the tape and reattach the drain surround.

Choosing Between Paint and Re-Plating

For most DIYers, high-temperature chrome spray paint is the most practical choice. It is inexpensive, easy to apply, and provides a decent chrome-like finish. However, it is not as durable as true chrome plating and may scratch or peel over time, especially in high-use areas. A brush-on nickel/chrome plating kit (available from specialty suppliers) electrochemically deposits a thin metal layer, which is more durable and looks more authentic, but it is messier and requires careful surface prep.

If the drain surround is a decorative piece that sees little water, paint is fine. If it is a kitchen sink drain that gets heavy use, consider re-plating or replacement. For deep pits that compromise the structural integrity of the base metal, replacement is the only safe option—a corroded drain can leak water into the cabinet below.

Common Mistakes to Avoid

  • Skipping the sanding steps: Going straight to paint over a pitted surface will leave visible bumps. You must sand to a smooth, even finish.
  • Using regular paint: Standard spray paint will not withstand hot water and cleaning chemicals. Always use high-temperature paint rated for at least 200°F.
  • Not removing all rust: Any rust left under the new coating will continue to corrode and cause the coating to fail. Use a rust converter or remover before sanding.
  • Overspray on the sink: Always protect the sink surface with tape and plastic, as chrome paint is difficult to remove once dry.
  • Applying thick coats: Thick coats of paint will run and drip, leaving an uneven finish. Multiple thin coats are better.

Cost and Time Comparison

A DIY restoration with spray paint costs roughly $15–$25 for materials (sandpaper, rust remover, paint, tape). The process takes about 2–3 hours of active work plus 24–48 hours of curing time. A brush-on plating kit costs $30–$60 and takes similar time. In contrast, a new chrome drain surround typically costs $10–$40 and can be installed in 30 minutes with basic tools. If the surround is in good shape except for a few pits, restoration is worth it; if it is heavily corroded or misshapen, replacement is cheaper and faster.

When to Replace Instead of Restore

Replace the drain surround if:

  • The base metal is soft, crumbling, or has holes (indicating severe corrosion).
  • The pits are larger than 1/8 inch in diameter or deeper than 1/16 inch.
  • The chrome is peeling off in large sheets, leaving large bare areas.
  • The drain surround is leaking or does not fit snugly against the sink.
  • You want a guaranteed, long-lasting result without the risk of a DIY finish failing.

Replacement is a straightforward job: unscrew the locknut under the sink, lift out the old surround, and drop in the new one. Ensure you use plumber’s putty or silicone sealant under the flange to prevent leaks.

Frequently Asked Questions

Can I use vinegar or lemon juice to remove rust from chrome? Yes, but only for light surface rust. Vinegar and lemon juice are mild acids that can dissolve rust, but they can also etch the chrome if left on too long. For pitted areas, a dedicated rust remover is safer and more effective.

Will chrome polish remove pits? No. Chrome polish only removes oxidation and minor scratches from the chrome surface. It cannot fill or smooth pits because the chrome layer is gone in those spots. You need to sand and refinish the surface.

How long will a spray-painted drain surround last? With proper prep and high-temperature paint, it can last 1–3 years under normal use. Abrasive cleaners and harsh chemicals will shorten its life. Clear coating can extend it.

Is it safe to use a drain surround with pits? Yes, as long as the base metal is intact and there are no leaks. Pits are a cosmetic issue. However, if the corrosion has weakened the metal, the surround could crack, so inspect it regularly.

Can I restore a drain surround without removing it from the sink? Yes, but it is trickier. You must tape off the sink surface carefully and work in a confined space. Removing it gives better access and a cleaner finish, but if you cannot remove it, the same steps apply.

What if the drain surround is brass, not chrome? If the surround is solid brass with a chrome finish, the same restoration steps apply. If it is unlacquered brass, you can polish it directly without painting, but it will tarnish over time.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →