sodcalculator

10 Tech How-To

Allow Ads on Specific Sites in Vivaldi Android

Guide 10-56846 · Updated · Step by step

Vivaldi for Android includes a built-in ad and tracker blocker. By default, it blocks ads everywhere, but you can allow ads on specific sites you want to support, like a favorite blog or a local news site. This guide walks you through adding a site to the exceptions list so ads load only where you choose.

What You’ll Need

  • Vivaldi for Android installed (version 6.0 or newer recommended).
  • The website address (URL) you want to allow ads on.
  • Access to the site’s settings menu in Vivaldi.

Step-by-Step

  1. Open Vivaldi on your Android device and navigate to the website where you want to allow ads.
  2. Tap the Vivaldi menu — the “V” icon in the bottom-right corner of the screen (or top-right on tablets).
  3. In the menu that slides up, tap the shield icon labeled “Block ads and trackers.” This opens the privacy panel for the current site.
  4. At the top of the panel, you’ll see the website’s address. Toggle off the switch next to “Block ads and trackers.” When the switch is gray, ad blocking is disabled for this site only.
  5. Reload the page by tapping the refresh icon in the address bar. Ads should now appear.
  6. To confirm the setting stuck, open the same menu again — the shield should show a small “off” badge or the switch should remain off.
  7. Repeat these steps for any other sites you want to allow ads on. Each site is remembered separately.

Common Mistakes

  • Turning off the global blocker instead of the per-site toggle. The menu has two controls: a master switch for all sites and a per-site switch. Make sure you’re toggling the one that says “for this site,” not the global one.
  • Not reloading the page. Changes to ad blocking only apply after a refresh. If ads don’t appear, reload once more.
  • Using the wrong URL. If you allow ads on example.com but visit www.example.com, the exception may not apply. Use the exact address shown in the address bar.
  • Confusing the shield with the site info icon. The shield is specifically for ad/tracker blocking. Tapping the padlock or “i” icon gives different options.

Tips

  • You can manage all your exceptions at once. Go to Settings → Privacy and security → Block ads and trackers, then tap “Exceptions.” From there, you can review or remove sites you’ve allowed.
  • If a site still shows broken layouts or missing videos after allowing ads, it may also be blocking trackers. Toggle the “Block trackers” switch off as well in the same panel.
  • Use this feature for sites you genuinely want to support. For everything else, keeping the blocker on saves data and speeds up browsing.
  • If you allow ads but the site still looks odd, try clearing the site’s cache: long-press the reload icon and choose “Hard reload.”

Troubleshooting

Ads still don’t appear after toggling off. First, check that you toggled the per-site switch, not the global one. Then reload. If that fails, close the tab and reopen the site. If ads still don’t show, the site may serve ads from a domain that Vivaldi’s tracker list blocks separately — toggle off “Block trackers” as well.

The switch keeps turning back on. This can happen if you’re using a sync profile that overrides local settings. Go to Settings → Sync and check whether “Privacy settings” is enabled in sync. If it is, disable it temporarily, set your exception, then re-enable.

You allowed ads but now see too many. Some sites use aggressive ad networks. You can’t fine-tune which ads appear, but you can remove the exception by going back to the shield menu and toggling the switch on again.

Other devices still block ads on that site. Per-site exceptions are stored per device unless you sync them. If you want the same exception on your tablet or desktop, you’ll need to set it manually on each device, or enable sync of privacy settings.

Frequently Asked Questions

Does allowing ads on one site affect other sites?

No. The exception applies only to the exact URL you set it for. All other sites keep the default blocking behavior.

Can I allow ads on a subdomain but not the main domain?

Yes. The exception is tied to the full hostname. Allowing shop.example.com does not affect example.com or news.example.com.

Will allowing ads slow down my browsing on that site?

Possibly. Ads and trackers add extra requests and data, so pages may load slower and use more bandwidth on that specific site. Other sites remain fast.

How do I remove a site from the allowed list?

Open the site, tap the shield, and toggle the block switch back on. Or go to Settings → Privacy and security → Block ads and trackers → Exceptions and delete the entry.

Does this work for embedded videos or iframes?

Usually yes, because the exception applies to the page’s network requests. However, if a video player loads from a separate domain that is still blocked, you may need to allow that domain too.

Is there a way to allow ads temporarily?

Not directly. You can toggle the shield off, browse, then toggle it back on. There is no built-in timer for temporary exceptions.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →