sodcalculator

10 Tech How-To

How to Board Up Windows Before a Storm

Guide 10-52112 · Updated · Step by step

Boarding up windows before a storm protects your home from flying debris and high winds, which are the most common causes of window breakage during hurricanes and severe storms. This guide walks you through measuring, cutting, and installing plywood panels so your windows have a solid defense. Before you start, confirm your window dimensions and gather the materials—most of which you can find at any hardware store.

What You’ll Need

  • Plywood (3/4-inch exterior-grade or marine-grade, CDX or better)
  • Measuring tape
  • Pencil and paper or a notepad
  • Circular saw or table saw
  • Drill with screwdriver bits
  • Galvanized wood screws (2 to 2.5 inches long) or storm shutter anchors
  • Wing nuts and bolts if using pre-installed anchors
  • Ladder (if windows are above ground level)
  • Safety glasses and work gloves
  • Pry bar (for removal later)

Step-by-Step

  1. Measure each window. Measure the width and height of the window opening from the outside, including the trim. Add 8 inches to both dimensions (4 inches on each side) so the plywood overlaps the frame by at least 2 inches on all sides. Write down each window’s measurements and label them (e.g., “living room left”).
  2. Cut the plywood. Using a circular saw or table saw, cut each panel to the measured size. If you have multiple windows of the same size, you can cut one panel and use it as a template for others. Always wear safety glasses and gloves.
  3. Pre-drill screw holes. On each panel, drill pilot holes about 6 inches apart along the edges, leaving 2 inches from the edge. This prevents the wood from splitting and makes installation faster. If you are using anchors, align holes with the anchor locations on your house.
  4. Label each panel. Write the window name on the back of the panel with a pencil or marker. This saves time when you need to reinstall them.
  5. Install anchors (optional but recommended). If you plan to use storm shutter anchors, install them into the wall around each window before the storm season. Place them about 6 inches from each corner and every 12-16 inches apart. Use a drill with a masonry bit if your walls are brick or concrete.
  6. Position the first panel. Place the plywood over the window, centering it so the overlap is even on all sides. Use a ladder if needed and have someone hold the panel while you work.
  7. Secure the panel. Drive screws through the pilot holes into the window frame or wall. If using anchors, insert bolts through the panel and tighten wing nuts. Make sure the panel is snug but not so tight that it warps the wood.
  8. Repeat for all windows. Work from one side of the house to the other, covering every window you plan to protect. Do not forget garage windows and sliding glass doors.
  9. Check for gaps. After all panels are up, inspect each one for gaps or loose edges. Add extra screws if needed to ensure a tight fit.
  10. Remove after the storm passes. Once the storm is over and it is safe, use a pry bar to gently remove the panels. Store them flat in a dry place, leaning against a wall or on a rack.

Common Mistakes

  • Using thin plywood. 3/8-inch or 1/2-inch plywood can shatter under high winds. Always use 3/4-inch exterior-grade.
  • Not overlapping enough. If the panel only covers the glass without overlapping the frame, wind can push it inward. You need at least 2 inches of overlap on every side.
  • Drilling directly into the window frame. This can damage the frame and let water in. Use anchors or screws into the wall around the window, not the frame itself.
  • Forgetting to label panels. When you need to reinstall them, you will waste time figuring out which panel goes where.
  • Waiting until the last minute. Measuring and cutting takes time. Do it well before the storm warning is issued.

Tips

  • Store screws and wing nuts in a labeled bag attached to each panel so they are ready to go.
  • If you have casement or awning windows that crank out, board them from the inside or remove the crank handles first.
  • Apply a water-repellent sealant to the plywood edges to extend its life.
  • For extra protection, use plywood rated for windborne debris (e.g., OSB with a rating) if local building codes require it.
  • Practice installing one panel before the storm so you know how long it takes and what tools you need.

Troubleshooting

Panel doesn’t fit. If you cut a panel too big, trim it with a saw. If it is too small, you can add a second layer or use a larger piece of plywood—never leave a gap.

Screws won’t grip. If the wall is masonry, you need masonry anchors. If the wood is rotted, move the screw location or use a toggle bolt.

Panel warps. Store plywood flat and keep it dry. If it warps, use extra screws to force it flat against the wall.

You run out of screws. Use any strong screw you have, but make sure it is long enough to penetrate the wall by at least 1 inch.

Window is too large for one sheet. Use two panels side by side, with a 2×4 brace over the seam to keep them together.

Frequently Asked Questions

Q: Can I use OSB instead of plywood?
Yes, but it is heavier and can swell if it gets wet. Plywood is generally easier to handle and more durable.

Q: How long does it take to board up a typical house?
With pre-cut panels and anchors, about 10-15 minutes per window. If you are cutting on the spot, allow 30 minutes per window.

Q: Do I need to board up all windows?
At least cover windows facing the prevailing wind and any large windows. But if the storm is severe, it is safest to cover all windows.

Q: Can I use plywood from a hardware store that is not exterior-grade?
It may not hold up in heavy rain. Use exterior-grade (CDX) or marine-grade for best results.

Q: What about sliding glass doors?
They need boarding too. Measure the entire door opening and use a large panel, or multiple panels secured together.

Q: Should I tape windows instead of boarding?
No. Taping does not prevent breakage and can make cleanup harder. Boarding is the only effective DIY method.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →