This guide walks you through charging AirPods 5 when you have the wireless charging case. It covers how to place the case on a Qi-certified charger, what the LED light means, and what to do if charging doesn’t start.
What You’ll Need
- AirPods 5 with their wireless charging case
- A Qi-certified wireless charging pad or mat (any brand that supports Qi works)
- A USB-C cable and power adapter for the charging pad (usually included with the pad, or you can use your phone’s charger)
- A clean, flat surface to place everything on
Step-by-Step
- Place both AirPods inside the case. Make sure each earbud is seated in its correct slot (left in the left slot, right in the right slot). They should click into place magnetically. Close the lid firmly.
- Plug in your wireless charging pad. Connect the pad to a power source using its USB-C cable and a wall adapter. Most pads have a small LED that lights up to show they have power. If your pad doesn’t have an indicator, just make sure it’s connected to a working outlet.
- Position the case on the charging pad. Place the AirPods case flat on the center of the pad. The case has a flat bottom and the charging coil is located in the lower half of the case, near the Lightning/USB-C port area. Align the case so that the status light faces up and the port side is roughly centered over the pad’s charging area. If your pad has a visible coil marking, center the case’s lower half on that marking.
- Check the status light. When you place the case on the pad, the status light on the front of the case should turn on. It will show amber if the case is charging, or green if it’s already fully charged. If the light doesn’t come on within a few seconds, lift the case and reposition it slightly, then try again.
- Leave it to charge. Keep the case on the pad until the light turns green. A completely drained case typically takes about 2 to 3 hours to reach 100% with a standard 5W Qi charger. You can keep using the AirPods while the case charges—just take them out and put them back when done.
- Unplug when done (optional). Once the light is green, you can remove the case from the pad. Leaving it on the pad won’t damage anything; the case stops drawing power when full. If you’re not using the pad for anything else, you can unplug it to save energy.
Common Mistakes
- Placing the case upside down. The case must sit flat on its bottom. If you place it on its side or upside down, the charging coil won’t align and nothing will charge.
- Using a non-Qi charger. Some cheap pads or older chargers use proprietary technology. Make sure your pad is Qi-certified. If it came with a phone that charges wirelessly, it’s almost certainly Qi-compatible.
- Leaving the lid open. The case charges with the lid closed or open, but it’s more stable and the light is easier to see with the lid closed. An open lid can also let dust get inside.
- Ignoring the light. If the status light doesn’t turn on, the case isn’t charging. Don’t assume it’s working just because it’s sitting on the pad.
- Charging through a thick case. If you have a third-party silicone or leather case on your AirPods case, remove it. Thick or metal cases can block the wireless signal.
Tips
- Use a 7.5W or 10W charger for faster charging. The AirPods case accepts up to about 5W, so a higher-wattage pad won’t charge it faster, but it won’t hurt. A 5W charger is perfectly fine.
- Keep the contacts clean. Wipe the bottom of the case and the pad with a dry, lint-free cloth occasionally. Dust and debris can reduce charging efficiency.
- Charge the case with the AirPods inside. This charges both the earbuds and the case at the same time. If you charge the case empty, the AirPods won’t gain any battery.
- Use the pad for multiple devices. Most Qi pads can charge your phone and AirPods case at the same time, though the case will charge slower if the pad splits its output.
- Check the light after a few minutes. Sometimes the light turns off after a few seconds when the case is full. If you just placed it and the light goes off, it’s probably already fully charged.
Troubleshooting
The status light doesn’t turn on at all. First, confirm the pad is powered—try charging your phone on it. If the phone charges, the pad works. Then reposition the case: move it slightly left, right, forward, or backward on the pad. The coil in the case is near the bottom edge, so try aligning that edge with the center of the pad. If it still doesn’t work, remove any case or accessory on the AirPods case and try again.
The light turns amber but never goes green. This usually means the case is charging but very slowly. Check that you’re using a pad that outputs at least 5W. Some older pads output only 2.5W, which will charge the case very slowly. Also, if the case is extremely hot or cold, charging may slow down or pause. Move it to a room-temperature location.
The case charges but the AirPods don’t. This happens when the AirPods aren’t seated properly. Open the lid, remove both earbuds, and reinsert them firmly until they click. Close the lid and place the case back on the pad. The AirPods should charge whenever they’re in the case and the case has power.
Charging works with a cable but not wirelessly. If you have a Lightning or USB-C cable, try that to confirm the case itself is fine. If wired charging works, the issue is alignment or the pad. Try a different Qi pad or reposition the case more carefully.
The case gets warm while charging. Slight warmth is normal. If it feels hot to the touch, unplug the pad and let it cool down. Then try a different pad or cable. Excessive heat can indicate a faulty charger or a problem with the case battery.
The light flashes orange. This usually indicates an error. Reset the case by holding the setup button (the small button on the back) for 15 seconds until the light flashes amber, then white. Re-pair the AirPods with your device if needed, then try charging again.
Frequently Asked Questions
Can I charge AirPods 5 with my iPhone’s MagSafe charger? Yes, if the MagSafe charger is Qi-certified, which all Apple MagSafe chargers are. The case will charge, though it won’t snap on magnetically like an iPhone does. Just place it flat on the MagSafe puck.
How long does a full charge last? The case holds multiple full charges for the AirPods. A fully charged case can recharge the AirPods about 4 to 5 times before the case itself needs charging. The AirPods themselves last about 5–6 hours of listening time per charge.
Can I use the AirPods while the case is charging? Yes. You can take the AirPods out and use them while the case sits on the charger. The case will continue charging, and the AirPods will charge when you put them back.
Is it bad to leave the case on the wireless charger overnight? No. The case has built-in overcharge protection. Once it reaches 100%, it stops drawing power. Leaving it on the pad overnight is safe and won’t degrade the battery faster than normal use.
Why does my case charge slower wirelessly than with a cable? Wireless charging is generally less efficient than wired. A standard Qi pad delivers about 5W, while a wired connection can deliver up to 20W. The case is designed to accept a maximum of about 5W wirelessly, so it will always be slower than a cable. This is normal and not a defect.
Can I charge the case with a phone that has reverse wireless charging? Yes, if your phone supports reverse wireless charging (like Samsung’s Wireless PowerShare or similar). Place the AirPods case on the back of your phone, centered on the charging coil area. The phone must have enough battery and the feature must be enabled in settings.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- View Android Photos on Chromebook: Step-by-Step
- Fix Windows Could Not Prepare the Computer to Boot
- Windows 11 Security Settings: Best Config Guide
- Set a Google Play Budget & Stop Accidental Purchases
- Destiny 2 Error Code Anteater: Fixes & Causes
- Install Custom Recovery on Samsung Galaxy Trend