Connecting two JBL Bluetooth speakers lets you fill a room with sound—either as a true left/right stereo pair or as two speakers playing the same music simultaneously for louder, room-filling audio. This guide walks you through the setup for both modes on current JBL speakers that support JBL Connect+, JBL Connect, or Auracast. Before you start, make sure both speakers are charged and within about 30 feet of each other and your phone.
What You’ll Need
- Two compatible JBL Bluetooth speakers (e.g., Flip, Charge, Pulse, Xtreme, Boombox, or newer models with Auracast)
- A smartphone, tablet, or computer with Bluetooth enabled
- The JBL Portable app (recommended for firmware updates and easy setup, but not strictly required for older Connect+ models)
Step-by-Step
For Speakers with JBL Connect+ (Flip 4/5, Charge 4, Pulse 4, Xtreme 2/3, Boombox 1/2)
- Power on both speakers. Press the power button on each speaker until you hear the power-on tone.
- Connect the first speaker to your phone. Go to your device’s Bluetooth settings and pair with the first JBL speaker as you normally would.
- Press the Connect+ button on the first speaker. This button has an icon that looks like a sideways hourglass or two interlocking arrows. It’s usually on the top or side of the speaker.
- Press the Connect+ button on the second speaker. Do this within a few seconds. The speakers will automatically search for each other and pair.
- Choose your mode. On the JBL Portable app (or by pressing the Connect+ button again on the first speaker), you can select either Stereo (left/right channels) or Party (both speakers play the same audio).
- Play your audio. Start music from your phone. Both speakers should output sound. To switch between stereo and party later, just press the Connect+ button on the first speaker again.
For Newer Speakers with Auracast (Flip 6, Charge 5/6, Pulse 5, Xtreme 3/4, Boombox 3)
- Update firmware. Open the JBL Portable app and install any available firmware updates on both speakers.
- Connect one speaker to your phone. Pair the first speaker via Bluetooth as usual.
- Open the JBL Portable app. Tap on the speaker icon for the connected speaker.
- Tap “Auracast” or “Connect.” The exact label varies by app version. You’ll see a list of nearby compatible speakers.
- Select the second speaker. Tap its name in the list to pair it.
- Choose Stereo or Party. The app will ask you to pick a mode. Select Stereo for left/right or Party for dual mono.
- Confirm and play. Hit “Done” and start your music. Both speakers will now play together.
For Older Speakers with JBL Connect (Flip 3, Charge 2+, Pulse 2, Xtreme)
- Power on both speakers. Ensure they’re in pairing mode (Bluetooth button).
- Connect the first speaker to your phone.
- Press the Connect button (icon of two speakers) on the first speaker.
- Press the Connect button on the second speaker. They will pair automatically.
- Note: These older models only support Party mode (same audio), not true stereo.
Common Mistakes
- Mixing incompatible generations: JBL Connect (older) and JBL Connect+ (newer) are not cross-compatible. Auracast speakers may also not work with older Connect+ models unless they support both protocols.
- Forgetting to update firmware: If you’re using Auracast speakers, outdated firmware can cause pairing failures.
- Pressing the wrong button: The Connect+ button is not the Bluetooth pairing button. Using the Bluetooth button will just put the speaker in discovery mode for a single connection.
- Expecting stereo on older models: Only Connect+ and Auracast support true stereo. Original Connect only does party mode.
- Having other Bluetooth devices interfering: If your phone is connected to a smartwatch or other audio device, it can confuse the connection.
Tips
- Keep speakers close together initially. Pair them within 3 feet of each other to ensure a strong handshake.
- Use the app for best control. The JBL Portable app gives you a visual indicator of which speaker is left/right and allows you to swap channels.
- Position for stereo: Place the left speaker to your left and the right speaker to your right, at ear level for the best imaging.
- For party mode, place speakers apart. To cover a large area, put the two speakers on opposite sides of the room.
- Charge both speakers fully. The battery drains evenly, but if one is low, it will shut off first and break the link.
- Remember the limit: You can usually connect up to 100 speakers with Connect+ (Auracast limits vary), but for most home use, two is plenty.
Troubleshooting
- Speakers won’t pair. Turn both speakers off and on again. Then press the Connect+ button on both speakers simultaneously. If that fails, reset the speakers (see below).
- Only one speaker plays. Check that the second speaker is not connected to another device (like a laptop). Disconnect it from all other Bluetooth sources and try again.
- Sound is out of sync. This is rare but can happen if the speakers are too far apart. Move them closer (within 10 feet) and restart the audio stream.
- Stereo mode sounds weird. Make sure you’re not sitting too close to one speaker—you’ll hear mostly that channel. Sit centered between them.
- App doesn’t show the second speaker. Update the app and firmware. If you’re using an iPhone, make sure Bluetooth is on for the JBL Portable app in Settings > Privacy > Bluetooth.
- Factory reset both speakers. For most JBL models, press and hold the Bluetooth and Volume Up buttons simultaneously for about 10 seconds until you hear a tone. This clears all pairings and lets you start fresh.
Frequently Asked Questions
Can I connect two JBL speakers of different models?
Yes, as long as both support the same connection technology (e.g., both have Connect+, or both have Auracast). For example, a Flip 5 and a Charge 4 can pair via Connect+. But a Flip 4 (Connect+) won’t pair with a Flip 6 (Auracast).
How many JBL speakers can I connect at once?
With JBL Connect+, you can link up to 100 speakers (though performance may degrade with many). With Auracast, the limit is typically 2 for stereo, but more for party mode depending on the source device. In practice, 2-10 is common.
Can I use two JBL speakers with a TV or computer?
Yes, if the TV/computer supports Bluetooth audio output. You pair the first speaker to the TV, then use the Connect+ button to add the second. However, audio lag may be noticeable with video, so a wired connection is better for movies.
Why is there no stereo option on my older JBL speakers?
Stereo mode was introduced with JBL Connect+. Older speakers with the original JBL Connect only support party mode (identical audio). Check your speaker’s manual or the app to see what’s available.
Do I need the JBL Portable app to connect two speakers?
For Connect+ speakers, you can use the physical buttons without the app—just press Connect+ on both. For Auracast speakers, the app is required to select the second speaker and choose the mode.
Will connecting two speakers drain the battery faster?
Yes, both speakers will drain at roughly the same rate, and the total battery life is about the same as using one speaker. The connection itself uses minimal power, but playing at higher volume will drain faster.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Fix msmpeg2vdec.dll Errors in Windows
- How to Update Sonos App and Speakers
- Unlock iPad Without Apple ID: Is It Possible?
- iOS 18 WhatsApp Notifications Not Working? Fix
- Fix Windows Cannot Locate Suitable Printer Driver
- Spotify Private Listening: Turn It On and Off