sodcalculator

10 Tech How-To

How to Find MAC Address in Windows 10

Guide 10-50844 · Updated · Step by step

This guide shows you several ways to view the MAC address (physical address) of your network adapters in Windows 10. You’ll learn how to find it using Settings, Command Prompt, and PowerShell, so you can identify your device on a network, set up MAC filtering, or troubleshoot connectivity issues.

What You’ll Need

  • A Windows 10 PC or laptop
  • Administrator rights (only needed for some methods, not all)
  • No additional software required

Step-by-Step

Method 1: Using Settings (Easiest)

  1. Click the Start button (Windows icon) and select the Settings gear icon.
  2. In the Settings window, click Network & Internet.
  3. Depending on your connection type:
    • Wi-Fi: Click Wi-Fi in the left sidebar, then click Hardware properties.
    • Ethernet: Click Ethernet in the left sidebar, then click your active network connection (e.g., “Ethernet”).
  4. Scroll down to the Properties section. You’ll see a line labeled Physical address (MAC) – that’s your MAC address. It looks like a series of six pairs of letters and numbers (e.g., 1A-2B-3C-4D-5E-6F).

Method 2: Using Command Prompt

  1. Press Windows key + R to open the Run dialog.
  2. Type cmd and press Enter (or click OK).
  3. In the Command Prompt window, type ipconfig /all and press Enter.
  4. Scroll through the output to find your active adapter (e.g., “Wireless LAN adapter Wi-Fi” or “Ethernet adapter Ethernet”).
  5. Look for the line labeled Physical Address – that’s your MAC address. It’s usually shown with dashes (e.g., 1A-2B-3C-4D-5E-6F).

Method 3: Using PowerShell

  1. Right-click the Start button and select Windows PowerShell (or Windows Terminal).
  2. Type getmac /v and press Enter.
  3. You’ll see a table with columns like “Connection Name”, “Network Adapter”, and “Physical Address”. The Physical Address column contains the MAC address for each adapter.

Common Mistakes

  • Looking at the wrong adapter: Many computers have multiple adapters (Wi-Fi, Ethernet, Bluetooth, virtual). Make sure you’re checking the one that’s actually connected to the network you care about.
  • Confusing MAC address with IP address: The MAC address is a permanent hardware identifier (like a serial number), while the IP address is a temporary network assignment. They are not the same.
  • Typing the command incorrectly: If you misspell ipconfig or getmac, you’ll get an error. Double-check your typing.
  • Using a VPN or virtual adapter: If you’re using a VPN, the MAC address shown might be from a virtual adapter, not your physical hardware. Disconnect the VPN temporarily if you need the real hardware MAC.

Tips

  • Copy the MAC address correctly: When you need to enter it into a router’s MAC filter or a registration form, copy it exactly as shown, including dashes or colons. Some systems prefer no separators – check the format required.
  • Use the “Physical Address” in ipconfig: In Command Prompt, the line is always labeled “Physical Address” – that’s the MAC address.
  • Check multiple adapters: If you’re troubleshooting, note the MAC addresses for both Wi-Fi and Ethernet – you might need either one.
  • Use PowerShell for a clean list: The getmac /v command gives a neat table, making it easy to spot the right adapter.

Troubleshooting

  • Command Prompt says “ipconfig is not recognized”: This is rare but can happen if the System Path variable is broken. Try using the full path: C:\Windows\System32\ipconfig.exe or use PowerShell instead.
  • No “Hardware properties” option in Settings: This option appears only when you’re connected to a network. If you’re not connected, connect to a Wi-Fi network or plug in an Ethernet cable, then check again.
  • You see multiple MAC addresses and don’t know which is which: The one that’s active usually has an IP address listed next to it in ipconfig /all. Look for the adapter with a “Default Gateway” or an IPv4 address that isn’t 0.0.0.0.
  • The MAC address changes: Some Windows settings allow “random hardware addresses” for Wi-Fi. If you see a different MAC each time you connect, go to Settings > Network & Internet > Wi-Fi and turn off “Random hardware addresses” if you need a stable one.

Frequently Asked Questions

What is a MAC address?

A MAC (Media Access Control) address is a unique identifier assigned to your network interface card (NIC) by the manufacturer. It’s used at the data link layer to identify devices on a local network.

Can I change my MAC address?

Yes, some network adapters allow you to change the MAC address through Device Manager or third-party tools. However, it’s usually not necessary and can cause network issues if done incorrectly.

Is the MAC address the same as the IP address?

No. The MAC address is a permanent hardware ID, while the IP address is a logical address assigned by your network (DHCP) and can change. Your router uses the MAC address to identify your device when assigning IPs.

How do I find the MAC address for a specific adapter like Bluetooth?

Use Command Prompt with ipconfig /all and look for the Bluetooth adapter section, or use PowerShell getmac /v to see all adapters listed.

Why would I need my MAC address?

Common reasons include setting up MAC address filtering on your router, registering a device on a restricted network (like a school or office), or troubleshooting network conflicts.

Does the MAC address appear in Windows 10 Settings?

Yes, in Settings > Network & Internet > Wi-Fi or Ethernet, click on “Hardware properties” and you’ll see the “Physical address (MAC)” listed.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →