Double hung guillotine windows are a classic window style where both sashes slide vertically. Over time, they can become difficult to open, stick, or even fall shut unexpectedly. This guide will walk you through the most common fixes: re-cording a broken sash cord, replacing worn weatherstripping, and adjusting the balance system. With basic tools and a little patience, you can restore smooth operation and improve your window’s energy efficiency.
What You’ll Need
- Flathead and Phillips screwdrivers
- Pry bar or putty knife
- Utility knife
- Pliers
- Hammer
- Replacement sash cord (cotton or nylon, same diameter as existing)
- Replacement weatherstripping (felt, vinyl, or metal)
- Wood shims or small blocks
- Sandpaper or a small plane (for easing stuck sashes)
- Lubricant (silicone spray or paraffin wax)
- Safety glasses and work gloves
Step-by-Step
- Remove the stop molding. Use a pry bar or putty knife to gently pry off the interior stop molding on the side(s) where the sash is stuck or the cord is broken. This molding holds the lower sash in place. Work slowly to avoid splitting the wood.
- Take out the lower sash. Tilt the lower sash inward and lift it out of the frame. Set it aside on a flat surface. If the sash is painted shut, run a utility knife along the edges to break the seal.
- Remove the upper sash (if needed). If the upper sash also needs attention, remove the parting bead (the thin strip between the sashes) by prying it out. Then lift the upper sash out.
- Inspect the sash cords and pulleys. With the sashes out, check each cord. If a cord is frayed or broken, remove the old cord from the sash and from the pulley. If the pulley is stiff, apply a few drops of lubricant.
- Replace a broken sash cord. Cut a new cord about 6 inches longer than the old one. Tie a knot at one end and thread the other end over the pulley and down into the sash weight pocket. Attach the cord to the weight (usually by threading through a hole and tying a knot). Then pull the cord so the weight is near the pulley, and staple or nail the cord to the sash channel at the correct height (the sash should be about 2 inches from the bottom when the weight is at the top). Reattach the cord to the sash using the existing screw or staple.
- Reinstall the sashes. Place the upper sash back in its tracks, then the lower sash. Ensure the cords are seated properly in the pulleys.
- Replace weatherstripping. While the sashes are out, remove old weatherstripping from the frame and sash. Cut new strips to length and press or nail them into place along the sides and top of the frame, and along the bottom of the lower sash.
- Ease sticking sashes. If a sash sticks due to paint or swelling, sand the edges lightly or use a plane to remove a thin layer. Be careful not to remove too much—only take off a little at a time.
- Reinstall stop molding and parting bead. Nail the stop molding back, ensuring it is snug but not too tight—the sash should still slide freely.
- Test the window. Operate the window several times. It should move smoothly and stay in place when left partially open.
Common Mistakes
- Breaking the stop molding. Prying too aggressively can split the wood. Use a wide putty knife and work from the top down.
- Cutting the new cord too short. If the cord is too short, the weight will hit the pulley before the sash is fully open. Always measure against the old cord or add extra length.
- Forgetting to secure the cord to the sash. If the cord is not properly attached, the sash will fall. Use a screw or staple that is firmly anchored.
- Over-tightening weatherstripping. If the weatherstripping is too thick or compressed too much, the window will stick. Use the correct size and install it so it just touches the sash.
- Removing too much wood from a sticking sash. Sanding too much creates gaps that let in drafts. Remove only a small amount and test frequently.
Tips
- Before disassembly, take a photo of the window to remember how the cords and weights are arranged.
- Use a cord that is the same diameter as the original to ensure it fits the pulley groove.
- If the window is painted shut, score the paint with a utility knife before prying.
- Lubricate the pulleys and the sash channels with a dry silicone spray—never oil, which attracts dust.
- If you have multiple windows, fix them one at a time to avoid mixing up parts.
- For older windows, consider replacing the cotton cord with a modern nylon cord that is more durable.
Troubleshooting
The window still won’t stay up. This usually means the cord is not attached to the weight correctly, or the weight is too light for the sash. Check that the knot is secure and that the weight is the correct size (typically 1-2 pounds for a standard sash). If the weight is missing, you may need to replace it with a similar one.
The window is still hard to slide. Check that the weatherstripping is not too thick and that the stop molding is not pressed too tightly. Also, inspect the sash channels for debris or old paint. Clean them out and apply a lubricant.
The sash cord keeps coming off the pulley. This can happen if the cord is too loose or the pulley is misaligned. Tighten the cord by adjusting the knot on the weight, or realign the pulley by loosening its mounting screws and repositioning it.
The window rattles in the wind. This is often due to worn weatherstripping or a loose stop molding. Replace the weatherstripping and ensure the stop molding is nailed securely.
The upper sash is stuck. If the upper sash won’t move, it may be painted shut or have a broken cord. Follow the same removal steps, but be extra careful with the parting bead—it is fragile and often breaks. If it does break, you can replace it with a new strip of wood.
Frequently Asked Questions
How often should sash cords be replaced?
Sash cords typically last 20-30 years, but they can wear out faster in humid climates or if they are exposed to direct sunlight. Inspect them annually for fraying or signs of wear.
Can I replace a sash cord without removing the window?
It is possible to access the cord through the weight pocket cover, but it is much easier to remove the sash first. Removing the sash gives you better access and ensures the cord is the correct length.
What type of cord should I use?
Use a braided cotton or nylon cord specifically designed for sash windows. It should be the same diameter as the original cord to fit the pulley. Nylon is more durable but can stretch over time.
My window has a spring balance instead of weights. How do I fix that?
Spring balances are common in newer windows. If the spring is broken, you’ll need to replace the entire balance unit. These are typically available at hardware stores and are installed by removing the sash and unscrewing the old balance.
Why does my window slam shut when I let go?
This is a sign that the counterweight (or spring balance) is too heavy or the cord is too short. Adjust the weight by adding or removing weight, or adjust the spring tension according to the manufacturer’s instructions.
Is it worth fixing an old guillotine window, or should I replace it?
If the frame is in good condition and the glass is intact, fixing the cords and weatherstripping is usually cost-effective and preserves the character of the home. If the frame is rotten or the glass is damaged, replacement may be a better long-term option.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Fix Slow Internet Lag on Samsung Galaxy Note
- iOS 18 Safari Not Working? Fixes That Help
- How to Check Your Linux Kernel for Spectre
- iPhone Safe Mode: How to Enable or Disable It
- How to Get iOS 17 on iPhone X (Safe Methods)
- Fix Gmail IMAP Error in Outlook: Step-by-Step