sodcalculator

10 Tech How-To

Fix Sony WH-CH720N Bluetooth Pairing & Connection Issues

Guide 10-46335 · Updated · Step by step

If your Sony WH-CH720N headphones are refusing to pair, keep dropping the connection, or won’t show up on your device, this guide walks you through the most effective fixes. We’ll cover the reset procedure, Bluetooth troubleshooting, and how to clear old pairings that cause conflicts.

What You’ll Need

  • Your Sony WH-CH720N headphones (charged)
  • The device you’re trying to connect to (phone, tablet, computer)
  • A USB-C cable (for charging, if battery is low)
  • Access to the device’s Bluetooth settings menu

Step-by-Step

  1. Charge the headphones. Plug them into a power source with the USB-C cable for at least 10 minutes. A low battery can prevent pairing or cause random disconnects. The red indicator light should be on while charging.
  2. Turn the headphones off and on. Slide the power button to the OFF position, wait 5 seconds, then slide it to ON. You should hear the power-on sound. This clears minor software glitches.
  3. Enter pairing mode manually. With the headphones off, press and hold the power button for about 7 seconds. The indicator light will start flashing blue and red rapidly, and you’ll hear “Bluetooth pairing” or a similar prompt. This is the correct pairing mode—do not just turn them on.
  4. On your source device, forget the headphones. Go to Bluetooth settings, find “WH-CH720N” in the paired devices list, and select “Forget” or “Remove.” This clears any stored connection data that might be corrupted.
  5. Pair again from scratch. With the headphones in pairing mode, on your device, scan for new devices and select “WH-CH720N” when it appears. Confirm any PIN prompt with 0000 (usually not required for these headphones).
  6. If pairing fails, reset the headphones. While the headphones are on, press and hold both the power button and the volume down (or the “NC/Ambient” button, depending on your model) simultaneously for about 10 seconds. The indicator light will flash blue four times, and the headphones will power off. This performs a factory reset, clearing all paired device memory.
  7. After reset, pair again. Turn the headphones back on and repeat steps 3–5 to pair them with your device as if they were new.
  8. If connection drops during use, check for interference. Move away from Wi-Fi routers, microwaves, and other wireless devices. Keep the source device within 30 feet (10 meters) and avoid thick walls or metal objects between them.
  9. Update firmware (if possible). Use the Sony | Headphones Connect app (available for Android and iOS) to check for firmware updates. An outdated firmware can cause connection bugs. The app also lets you reset the headphones to factory settings.

Common Mistakes

  • Not entering pairing mode correctly. Simply turning the headphones on does not put them in pairing mode. You must hold the power button for about 7 seconds until the light flashes red and blue.
  • Forgetting to remove old pairings. Leaving the headphones paired to multiple devices can cause them to auto-connect to the wrong one, or fail to connect to the one you want. Always forget the device in Bluetooth settings before re-pairing.
  • Ignoring battery level. A critically low battery can prevent the Bluetooth radio from functioning properly, even if the headphones seem to turn on.
  • Holding the reset buttons too briefly. The reset requires a full 10 seconds of holding both buttons. If you release early, nothing happens.
  • Using the wrong reset button combo. Some Sony models use different button combinations. For WH-CH720N, it’s the power button and the volume down button. Check your manual if unsure.

Tips

  • Use the Sony | Headphones Connect app. It gives you a clear view of the connection status, lets you switch between devices, and often resolves minor issues by re-syncing the connection.
  • Keep the headphones charged above 20%. Low battery is a common cause of intermittent disconnects.
  • Disable Bluetooth on devices you aren’t using. If you have the headphones paired to a laptop and a phone, and both are on, the headphones may keep switching between them. Turn off Bluetooth on the device you’re not using.
  • If using a Windows PC, remove the device from “Devices and Printers” as well. Sometimes Windows keeps a ghost driver that interferes with re-pairing.
  • Try pairing with a different device. This helps you determine whether the problem is with the headphones or with your original source device.

Troubleshooting

Headphones won’t enter pairing mode: Make sure they are off. If they turn on instead of entering pairing mode, you’re not holding the power button long enough. Hold for a full 7–10 seconds until you see the rapid red/blue flashing.

Headphones pair but immediately disconnect: This often means the battery is too low. Charge for at least 30 minutes. If that doesn’t help, perform a factory reset (step 6) and re-pair.

Headphones connect but no sound: Check that the volume is turned up on both the headphones and the source device. Also ensure that the source device is not sending audio to a different output (e.g., speakers). In Windows, right-click the volume icon and select “Open Sound settings” to verify the output device.

Headphones show as “Connected” but audio is choppy: This is usually interference or distance. Move closer to the source, and turn off Wi-Fi on the source if it’s on the 2.4 GHz band (common cause of Bluetooth interference).

Reset didn’t work: Try resetting again, but this time, after the reset, also delete the headphones from your device’s Bluetooth list (if it still appears) before re-pairing. If the problem persists, the Bluetooth antenna or module may be faulty, and you should contact Sony support.

Headphones are not discoverable: If they have been paired to another device recently, they may auto-connect to that device instead of entering pairing mode. Turn off Bluetooth on that other device, then try pairing again.

Frequently Asked Questions

Q: How do I factory reset my Sony WH-CH720N?
A: While the headphones are on, press and hold the power button and the volume down button simultaneously for about 10 seconds. The indicator light flashes blue four times, and the headphones turn off. This clears all paired devices.

Q: Why won’t my WH-CH720N enter pairing mode?
A: The most common reason is that you’re not holding the power button long enough. You need to hold it for about 7 seconds from the off state. Also, ensure the headphones are not already connected to another device—if they are, turn off Bluetooth on that device first.

Q: Can I connect my WH-CH720N to two devices at once?
A: Yes, these headphones support multipoint connection, allowing you to pair with two devices simultaneously. To use this, pair with the first device, then put the headphones back into pairing mode and pair with the second device. The headphones will switch between them automatically.

Q: Why does my WH-CH720N keep disconnecting from my laptop?
A: This is often due to interference or power saving settings on the laptop. Try disabling Bluetooth power saving in Device Manager (Windows) or Energy Saver settings (macOS). Also, make sure the headphones are charged and not too far from the laptop.

Q: How do I clear the Bluetooth pairing list on my WH-CH720N?
A: Perform a factory reset as described above. This will erase all paired devices, and the headphones will enter pairing mode automatically the next time you turn them on.

Q: My WH-CH720N are not showing up in the Bluetooth list on my phone. What should I do?
A: Make sure the headphones are in pairing mode (flashing red/blue light). If they still don’t appear, turn off Bluetooth on your phone, wait 10 seconds, then turn it back on. Also, check if your phone’s Bluetooth cache is full—clearing it from the system settings can help.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →