This guide walks you through fixing the “The disk structure is corrupted and unreadable” error in Windows. This error typically appears when you try to access an external drive, USB stick, or internal partition, and it prevents you from opening files or formatting the drive. You’ll need to use Windows built-in tools like Command Prompt and Disk Management, and possibly a third-party data recovery tool if the drive contains important data.
What You’ll Need
- A Windows PC (Windows 10 or 11 recommended)
- Administrator account access
- The affected drive connected (if external, use a direct USB port, not a hub)
- Optional: a second computer or external enclosure to test the drive
Step-by-Step
- Back up your data if possible. If you can access the drive at all, copy important files to another location immediately. If you can’t, skip to step 2 and consider using data recovery software before any repair attempts.
- Run CHKDSK to repair file system errors.
- Press
Windows + Xand select Command Prompt (Admin) or Windows PowerShell (Admin). - Type
chkdsk X: /f /r(replaceXwith the drive letter of the corrupted drive) and press Enter. - If the drive is in use, you’ll be prompted to schedule the check for the next restart. Type
Yand restart. - Wait for the scan to complete. This can take hours on large drives. Do not interrupt it.
- Press
- If CHKDSK fails, try a different command. In the same admin Command Prompt, run
chkdsk X: /f(without /r) orchkdsk X: /scan(Windows 10/11). Sometimes a less aggressive scan works. - Use DiskPart to clean the drive (only if you don’t need the data).
- Open admin Command Prompt again.
- Type
diskpartand press Enter. - Type
list diskto see all drives. Note the disk number of the corrupted drive (be careful: don’t confuse it with your system drive). - Type
select disk X(replace X with the correct number). - Type
cleanand press Enter. This wipes the entire disk, removing all partitions and data. - Type
exitto close DiskPart.
- Re-initialize and format the drive.
- Press
Windows + Xand select Disk Management. - Find the disk you just cleaned. It will show as “Unallocated”.
- Right-click the unallocated space and select New Simple Volume.
- Follow the wizard, assign a drive letter, and choose a file system (NTFS for large drives, exFAT for compatibility with Mac/consoles).
- Complete the wizard. The drive should now be accessible.
- Press
- If the drive still shows as RAW or unreadable after formatting, try a low-level format. Use the
format X: /FS:NTFScommand in admin Command Prompt (replace X with the drive letter). This can take a long time. - Check physical connections. If the drive is external, try a different cable, a different USB port (preferably USB 3.0 or higher), or another computer. For internal drives, check the SATA/power cables are firmly connected.
- Update or reinstall the disk driver.
- Press
Windows + Xand select Device Manager. - Expand Disk drives, right-click your drive, and select Uninstall device.
- Restart your PC. Windows will reinstall the driver automatically.
- Press
Common Mistakes
- Running CHKDSK on the wrong drive. Double-check the drive letter. Running CHKDSK on your system drive (usually C:) can cause issues if you don’t know what you’re doing.
- Interrupting CHKDSK. Let it finish. Stopping it mid-scan can worsen corruption.
- Using DiskPart without backing up. The
cleancommand erases everything permanently. If you haven’t backed up, you’ll lose all data. - Ignoring physical damage. If the drive makes clicking or grinding noises, it’s likely physically failing. Software fixes won’t help, and further attempts could make it worse.
- Formatting a drive that contains important data. Always try data recovery first if you need files.
Tips
- Use a reliable data recovery tool like Recuva, EaseUS Data Recovery Wizard, or Disk Drill before attempting any repairs if you need files. They can often recover data from corrupted drives.
- If the drive is under warranty, check with the manufacturer. Some have free recovery services.
- Keep your Windows system updated. Sometimes the error is caused by a bug that Microsoft has already fixed.
- For external drives, always use “Safely Remove Hardware” before unplugging to prevent corruption.
- If the drive is old (5+ years), consider replacing it even after a successful repair, as corruption often indicates impending failure.
Troubleshooting
If the steps above don’t work, try the following:
- CHKDSK says “Access denied” or “The disk is write-protected”: Remove any write-protection switch on the drive (on SD cards or USB sticks). If it’s a hardware switch, slide it to the unlocked position. If not, run
diskpart, select the disk, and typeattributes disk clear readonly. - The drive doesn’t appear in Disk Management at all: This indicates a hardware issue. Try the drive on another computer. If it doesn’t show up there, the drive is likely dead or the enclosure is faulty. Try replacing the enclosure.
- CHKDSK gets stuck at a certain percentage: Wait at least an hour. If it’s still stuck, force restart (hold the power button), then try again with
chkdsk X: /fonly. If that fails, the drive may be too damaged for software repair. - The drive formats but shows errors again: Run
chkdsk X: /ragain after formatting. If errors persist, the drive has bad sectors. Use a tool like HD Tune or CrystalDiskInfo to check the SMART status. If it shows “Caution” or “Bad”, replace the drive. - You get an “I/O device error” during any operation: This is a hardware-level error. Try a different cable, port, or computer. If the error persists, the drive is failing and you should stop using it immediately.
Frequently Asked Questions
Can I fix this error without losing data?
Sometimes, if the corruption is logical, CHKDSK can repair the file system without erasing files. However, if the drive is physically damaged, data loss is likely. Always attempt data recovery first if you need files.
What does “RAW” file system mean?
RAW means Windows cannot recognize the file system (like NTFS or FAT32). This often happens after corruption or improper ejection. The drive may still contain data, but Windows can’t read it without a repair.
How long does CHKDSK take?
It depends on the drive size and speed. A 1TB external drive can take several hours. A 4TB drive might take overnight. Don’t interrupt it.
Is this error a sign that my drive is dying?
It can be. Corruption often precedes physical failure. If the error recurs after a successful repair, back up your data and consider replacing the drive.
Can I use third-party software to fix this?
Yes, tools like MiniTool Partition Wizard, AOMEI Partition Assistant, or EaseUS Partition Master can sometimes repair corrupted drives with a GUI interface. They are useful if you’re uncomfortable with Command Prompt.
Will formatting the drive fix the error?
Yes, formatting will create a new file system and make the drive accessible again. However, it erases all data. Use this as a last resort after trying recovery.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Fix Apps Not Downloading From Play Store
- Secure a Samsung Galaxy After a Zero-Day Disclosure
- What to Check Before Installing Linux Alongside Windows
- Fix OEM Activation Error 0xc004c060 in Windows 10
- Why Does My App Run One Query for the List and One per Item?
- Fix Google Chrome Has Stopped Working