If you plug in a USB device and Windows 10 shows “Unknown USB Device (Port Reset Failed)” in Device Manager, the device won’t work and the error usually points to a power or driver issue on that specific port. This guide walks you through the most reliable fixes, from simple power cycling to updating USB controllers, so you can get the device recognized again.
What You’ll Need
- Administrator access to the Windows 10 PC (to change device settings and uninstall drivers).
- The USB device that’s failing, and ideally a different USB device (like a mouse or flash drive) to test the port.
- A second USB port (front or back of the PC) for testing.
- Optional: a USB hub with its own power supply if the device draws a lot of power.
Step-by-Step
- Unplug the device and restart Windows. Remove the USB device, then restart your PC. After Windows loads, plug the device back into the same port. This clears temporary glitches in the USB stack.
- Try a different USB port. Plug the device into another port, preferably one directly on the motherboard (back of the tower) rather than a front-panel port or hub. If it works, the original port may be damaged or have a power issue.
- Check the physical connection. Inspect the USB connector and the port for dirt, bent pins, or damage. Try a different cable if the device uses a detachable one.
- Update or reinstall the USB driver in Device Manager. Right-click the Start button and select Device Manager. Expand Universal Serial Bus controllers. Look for the “Unknown USB Device (Port Reset Failed)” entry (often with a yellow triangle). Right-click it and select Uninstall device. Then click Action > Scan for hardware changes. Windows will reinstall the driver.
- Disable USB selective suspend. This power-saving feature can interrupt communication. Open Control Panel > Power Options. Click Change plan settings next to your active plan, then Change advanced power settings. Expand USB settings > USB selective suspend setting and set it to Disabled for both “On battery” and “Plugged in”. Click OK and restart.
- Run the built-in hardware troubleshooter. Go to Settings > Update & Security > Troubleshoot > Additional troubleshooters. Select Hardware and Devices and run it. Follow any prompts.
- Check for Windows updates. Go to Settings > Update & Security > Windows Update and click Check for updates. Install any pending updates, especially driver and firmware updates, then restart.
- Update the chipset drivers. Visit your PC or motherboard manufacturer’s support website and download the latest chipset drivers (Intel, AMD, etc.). Installing these can fix USB controller issues.
- Reset the USB controller. In Device Manager, under Universal Serial Bus controllers, right-click each entry named Host Controller or Root Hub and select Uninstall device. Restart your PC. Windows will reinstall them automatically.
- Use a powered USB hub. If the device requires more power than the port can supply (common with external hard drives, printers, or VR headsets), plug it into a powered USB hub. This provides stable power and can eliminate the port reset error.
Common Mistakes
- Only trying the same port. If the port itself is faulty, the error will persist no matter what you do to drivers.
- Skipping the restart after uninstalling drivers. Uninstalling a USB controller without restarting can leave the system in an inconsistent state.
- Using a cheap or damaged USB cable. A marginal cable can cause intermittent connections that trigger the port reset error.
- Forgetting to disable selective suspend. This is a common fix and easy to overlook.
Tips
- Always try the device on another computer. If it fails there too, the device itself is likely faulty.
- Keep your USB controllers updated through Windows Update or the manufacturer’s site.
- For desktop PCs, use the USB ports on the back panel for high-power devices.
- If you have many USB devices, disconnect some to reduce power load on the controller.
Troubleshooting
If the error persists after following all steps:
- Boot into Safe Mode. Restart your PC and press F8 (or Shift + Restart) to enter Safe Mode. If the device works there, a third-party driver or software is interfering. Uninstall recently installed programs or drivers.
- Check the Device Manager for “Unknown USB Device (Device Descriptor Request Failed)”. This is a different error that often indicates a hardware problem with the device itself. Try a different cable or the device on another PC.
- Update the BIOS/UEFI. A BIOS update can improve USB compatibility. Check your motherboard manufacturer’s site for instructions.
- Disable Fast Startup. Go to Control Panel > Power Options > Choose what the power buttons do > Change settings that are currently unavailable. Uncheck Turn on fast startup and restart. This can resolve driver loading issues.
- Use the Windows Media Creation Tool to repair the system. If nothing else works, you can do a repair install (keeps your files) or reset Windows. Back up your data first.
Frequently Asked Questions
Why does my USB device say “Port Reset Failed”?
This error means Windows tried to reset the USB port because the device stopped responding, but the reset itself failed. It’s often caused by power issues, faulty cables, or outdated USB drivers.
Can a USB hub fix this error?
Yes, a powered USB hub can help if the device needs more power than the port provides. It supplies stable power, which can prevent the reset failure.
Will uninstalling USB drivers harm my computer?
No. Windows will automatically reinstall the correct drivers when you restart or scan for hardware changes. It’s a safe troubleshooting step.
Is this error caused by a virus?
No, it’s a hardware or driver issue, not a malware symptom. However, if you suspect malware, run a full antivirus scan separately.
Does this error affect all USB ports?
Usually it affects only the specific port or device. If all ports fail, the problem is likely the USB controller or the device itself.
Can I fix this error without restarting?
You can try uninstalling the device in Device Manager and scanning for hardware changes, but a restart is often necessary to fully reset the USB controller.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- How to Turn Off Shutter Sound on iPhone
- VPN Setup on iPhone SE: Step-by-Step Guide
- Fix Internet Not Working on Windows 11
- Fix Right Click Not Working in Firefox
- Compare Two Columns with Comma Separated Values in Excel
- How to Limit Ad Tracking on iPhone Apps