If your Mac isn’t recognizing a USB drive, flash drive, or external hard drive, this guide walks you through the most common fixes, from simple cable checks to resetting the SMC. You’ll need your Mac, the USB device, and a few minutes to try each step in order.
What You’ll Need
- Your Mac (any model running macOS Catalina or later)
- The USB device that isn’t being detected
- A different USB cable (if the device uses one) and a different USB port
- Another computer (optional, for testing the device)
Step-by-Step
- Check the physical connection. Unplug the USB device and plug it back in firmly. Try a different USB port on your Mac—preferably one directly on the computer rather than through a hub or dock. If you’re using a USB-C to USB-A adapter, make sure it’s snug.
- Try a different cable or adapter. Cables are a common failure point. If you’re using a third-party cable or hub, swap it for the original or a known-good one. Even if the cable charges your phone, it may not support data transfer.
- Test the device on another computer. Plug the USB device into a different Mac or a Windows PC. If it works there, the device is fine and the issue is with your Mac’s settings or ports. If it doesn’t work on any computer, the device itself may be faulty.
- Restart your Mac. A simple restart clears temporary glitches in the USB controller. Click the Apple menu > Restart, then wait for it to boot and try the device again.
- Check Disk Utility. Sometimes the device is detected but not mounted. Open Finder > Applications > Utilities > Disk Utility. Look in the left sidebar for your USB device—it may appear under “External” even if it doesn’t show on the desktop. If you see it, select it and click the “Mount” button (the play icon) at the top of the window.
- Reset the SMC (System Management Controller). The SMC manages low-level hardware including USB power. The reset method depends on your Mac:
- Intel Mac with T2 chip: Shut down, then press and hold Control + Option (Alt) + Shift on the left side of the keyboard, plus the power button, for 10 seconds. Release all, then press the power button to turn it on.
- Intel Mac without T2 (older models): Shut down, then press and hold Shift + Control + Option on the left side and the power button for 10 seconds. Release all, then turn on.
- Apple Silicon (M1/M2/M3): The SMC reset isn’t needed; simply restart your Mac. If the issue persists, try shutting down, waiting 30 seconds, and turning it back on.
- Reset the NVRAM (Intel Macs only). Shut down, then press the power button and immediately hold Command + Option + P + R for about 20 seconds. Release when you hear the startup chime a second time (or see the Apple logo appear and disappear twice on newer models).
- Check System Information. Hold the Option key and click the Apple menu > System Information (or System Profiler). Under “Hardware,” click “USB.” Look for your device in the list. If it appears with a warning icon or “Not enough power,” the port may not be providing enough power—try a powered USB hub.
- Update macOS and firmware. Go to System Settings > General > Software Update and install any pending updates. Also check for firmware updates by clicking “More Info…” if available. Restart after updating.
- Try Safe Mode. Restart your Mac and immediately hold the Shift key until you see the login window. In Safe Mode, macOS loads only essential extensions. If the USB works in Safe Mode, a third-party kext or login item is interfering. Restart normally to exit Safe Mode, then remove recently installed software.
Common Mistakes
- Using a charge-only cable. Many USB cables, especially for phones, only carry power and no data. Always test with a cable you know supports data.
- Plugging into a hub or keyboard port. Unpowered hubs often don’t provide enough power for larger drives. Connect directly to the Mac.
- Ignoring the device in Disk Utility. The drive may be mounted but not visible on the desktop because Finder settings hide external disks. Check Finder > Settings > General and make sure “External disks” is checked.
- Skipping the SMC reset. Many users try software fixes first, but the SMC reset resolves a large percentage of USB detection issues on Intel Macs.
- Assuming the device is dead. A device that works on another computer isn’t dead—the problem is on your Mac, so keep troubleshooting.
Tips
- Use a powered USB hub for high-power devices like external hard drives that need more than 5V/0.5A from a standard port.
- Format USB drives as exFAT if you need to use them with both Mac and Windows. macOS can read NTFS but not write to it without third-party software.
- Keep your USB ports clean and free of dust; a can of compressed air can help.
- If you frequently have issues, try a USB-C to USB-A adapter that supports USB 3.0 or higher for faster data transfer.
Troubleshooting
If the steps above didn’t work, here’s what to try next:
- If the device appears in System Information but not on the desktop: Open Disk Utility and try mounting the volume. If it fails, the drive may have a corrupt file system. Use First Aid (in Disk Utility) to repair it, but note this can erase data if the drive is badly damaged.
- If the device doesn’t appear anywhere: Try a different device in the same port. If that works, the port is fine and the original device is likely faulty. If no device works, the port itself may be damaged—contact Apple Support or a certified technician.
- If you get a “Device was not ejected properly” message repeatedly: This often means the drive is disconnecting during use. Try a different cable, a powered hub, or check the drive’s health with Disk Utility > First Aid.
- If the issue started after a macOS update: Some updates reset privacy settings or USB permissions. Go to System Settings > Privacy & Security > Accessibility and ensure any relevant apps have permission. Also check System Settings > General > Login Items & Extensions for leftover kernel extensions from old devices.
- If all else fails: Create a new macOS user account (System Settings > Users & Groups) and test the USB there. If it works, the issue is tied to your user account’s preferences or caches. You can migrate your data to the new account or reset your home folder permissions using Disk Utility’s First Aid on your startup disk.
Frequently Asked Questions
Why does my USB drive work on Windows but not on my Mac?
This is usually a file system issue. If the drive is formatted as NTFS, macOS can read it but not write to it. If it’s exFAT or FAT32, it should work on both. If it’s APFS or HFS+, Windows can’t read it without third-party software. Check the format in Disk Utility and reformat to exFAT if you need cross-platform compatibility.
How do I know if my USB port is dead?
Plug a known-good device (like a mouse or phone) into the port. If it doesn’t work, the port is likely dead. You can also check System Information > USB to see if the port is listed at all. If no device is detected and other ports work, the port may need repair.
Can a USB hub cause detection issues?
Yes. Unpowered hubs often don’t provide enough power for high-draw devices, and some hubs have compatibility issues with macOS. Try connecting directly to the Mac, or use a powered hub with its own AC adapter.
Will resetting the SMC erase my data?
No. Resetting the SMC only resets hardware settings like power management and fan control. It does not affect your files, apps, or personal data.
My USB drive shows up but I can’t open it—what should I do?
This usually means the file system is corrupted. Open Disk Utility, select the drive, and click “First Aid.” If that fails, you may need to reformat the drive, which will erase all data. Try connecting to another computer to back up files first if possible.
Is there a way to force macOS to detect a USB device?
You can try unplugging the device, waiting 10 seconds, and plugging it back in. If that fails, restart your Mac with the device plugged in. Some users also report success with resetting the SMC (Intel Macs) or simply toggling Bluetooth off and on, which can reset the USB stack in rare cases.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Windows 11 Calendar Wrong Day? Fix It Here
- How to Use curl Command in Linux
- Install ChromeOS: Convert Laptop to Chromebook
- Fix OneNote App Not Working on Android
- Move Games to SSD Without Reinstalling
- Move Windows 11 Taskbar to Top or Side: Easy Steps