Installing house wrap around existing windows seals the rough opening against air and water intrusion, preventing drafts, rot, and mold. This guide walks you through the process of cutting, folding, and flashing the wrap so it integrates correctly with the window frame and the surrounding wall. You’ll need basic tools and about an hour per window, depending on accessibility.
What You’ll Need
- House wrap (polyethylene or similar, enough to overlap the window opening by at least 6 inches on all sides)
- Utility knife with a sharp blade
- Stapler with 1/2-inch or 3/4-inch staples (or cap nails for thicker wraps)
- Flashing tape (self-adhered, 4-inch wide, compatible with the wrap)
- Straightedge or a long level (for cutting straight lines)
- Scissors (heavy-duty, for cutting tape)
- Caulk gun and exterior-grade sealant (if the existing window has gaps)
- Utility knife blades (extra)
- Ladder or step stool (if working above ground)
- Safety glasses and work gloves
Step-by-Step
- Prepare the area. Clean the window frame and the surrounding wall of dirt, old caulk, or loose paint. Ensure the surface is dry. If the existing window has any gaps between the frame and the rough opening, fill them with exterior-grade sealant and let it cure according to the manufacturer’s instructions.
- Cut the house wrap to size. Measure the window width and height. Add 12 inches to both dimensions (6 inches on each side). Cut a rectangular piece of house wrap that size. For a typical 36×48-inch window, you’ll need a 48×60-inch piece.
- Position the wrap over the window. Hold the cut piece centered over the window opening, with the bottom edge overlapping the sill by at least 6 inches. The wrap should be smooth, not stretched tight, and free of wrinkles.
- Staple the top edge first. Starting at the top center, staple the wrap to the wall sheathing about 1 inch from the top edge. Work outward toward the corners, placing staples every 6 to 8 inches. Leave the bottom and sides loose for now.
- Cut the X across the window opening. With the wrap still covering the window, use a utility knife to cut an X from corner to corner of the window opening. Start at the top left corner of the window frame and cut diagonally to the bottom right corner. Repeat for the other diagonal. The cuts should go just to the inside edge of the window frame, not beyond it.
- Fold the top flap up. Take the top triangular flap (above the window) and fold it up and over the top of the window frame. Pull it tight and staple it to the sheathing above the window. This flap will later be covered by the top flashing.
- Fold the side flaps inward. Take the left and right triangular flaps and fold them into the window opening, tucking them against the sides of the window frame. Pull them snug and staple them to the inside of the rough opening (the side jambs). Do not staple over the window frame itself; staple only to the wood sheathing.
- Fold the bottom flap down. Take the bottom triangular flap and fold it down over the sill, pulling it tight. Staple it to the sheathing below the window. This flap should overlap the side flaps slightly.
- Apply flashing tape to the bottom. Cut a piece of flashing tape slightly wider than the window opening (about 4 inches wider). Center it over the bottom of the window, pressing it firmly over the wrap and the sill. Start at the center and work outward, pressing out air bubbles. The tape should extend at least 2 inches up the sides of the window frame.
- Apply flashing tape to the sides. Cut two pieces of tape, each about 6 inches longer than the window height. Apply one to each side, overlapping the bottom tape. Press firmly, again working from the center outward. The tape should cover the side flaps and extend onto the window frame by about 1 inch.
- Apply flashing tape to the top. Cut a piece of tape the same width as the bottom piece. Apply it over the top flap, overlapping the side tapes. This creates a shingle effect: water flows from top to bottom, over each successive layer.
- Trim excess wrap. Use a utility knife to trim any excess wrap that extends beyond the window frame or looks messy. Cut cleanly along the edge of the tape.
- Seal the edges. Run a bead of exterior-grade sealant along the top edge of the top tape and the outer edges of the side tapes, if the manufacturer recommends it. This is optional but adds extra protection.
- Inspect your work. Check that all flaps are covered by tape, there are no gaps or tears in the wrap, and the tape is firmly adhered. Repair any damage immediately with additional tape.
Common Mistakes
- Stapling through the tape: Staples through flashing tape create holes that let water in. Staple the wrap first, then apply tape over the staples.
- Cutting the X too large: If you cut beyond the window frame, you’ll create gaps in the wrap that are hard to patch.
- Not overlapping the flashing correctly: The top tape must overlap the side tapes, and the side tapes must overlap the bottom tape. Reversing this order directs water into the wall.
- Leaving wrinkles or bubbles: Wrinkles in the wrap or tape can create channels for water. Smooth them out as you go.
- Using the wrong tape: Regular duct tape or masking tape will fail. Use only self-adhered flashing tape rated for house wrap.
- Skipping the sealant on gaps: If the window frame is not flush with the sheathing, gaps remain that tape cannot bridge. Fill them first.
Tips
- Work on a dry day with temperatures above 40°F (4°C) for best adhesion of the tape.
- Use a straightedge and a sharp blade to cut the X cleanly. A dull blade will tear the wrap.
- If the window is large, have a helper hold the wrap while you staple.
- Keep the wrap taut but not stretched. Over-stretching can cause it to tear at the corners.
- For extra protection, apply a bead of sealant under the bottom flap before taping.
- If you’re installing new windows, do the house wrap before setting the window, but this guide assumes the window is already in place.
Troubleshooting
- Tape won’t stick: The surface may be dusty or damp. Clean with a dry cloth and ensure the temperature is above the tape’s minimum application temperature (usually 40°F). If it still won’t stick, use a primer recommended by the tape manufacturer.
- Wrap tears during installation: Cut a patch of wrap at least 2 inches larger than the tear, apply it over the tear, and secure with tape on all edges.
- Water pools on the sill: This indicates the bottom flap is not sloped away from the window. Fold the flap down and outward, creating a slight slope. You may need to add a piece of wood or shim under the wrap to create a positive slope.
- Window is too close to the wall edge: If you cannot get 6 inches of wrap around the window, use a wider piece of wrap or apply a second layer of tape to extend the flashing.
- Existing caulk or paint prevents adhesion: Scrape away loose material and wipe with a solvent recommended for the wrap. Do not rely on tape over peeling paint.
- You accidentally staple through the window frame: Remove the staple and seal the hole with exterior-grade sealant. Avoid stapling in the same spot again.
Frequently Asked Questions
Can I install house wrap over old siding?
No. House wrap must be applied directly to the sheathing, not over siding. Remove the siding around the window first.
Do I need to remove the window to install house wrap?
No, this method works with the window in place. You cut the wrap around the frame and tuck the flaps into the opening.
What is the best order for flashing tape?
Bottom first, then sides, then top. This creates a shingle effect that sheds water outward.
Can I use house wrap tape instead of flashing tape?
House wrap tape is for sealing seams in the wrap itself. Flashing tape is wider, more flexible, and designed for window openings. Use flashing tape for this job.
How long will the house wrap last?
Quality house wrap can last 20 years or more when installed correctly and protected from UV exposure. Once covered by siding, it lasts indefinitely.
Should I staple or nail the house wrap?
Staples are fine for most wraps. Cap nails are better for windy areas because they hold better. Avoid using a hammer and nails without caps, as they can tear the wrap.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- How to Enable Privacy Indicators on Chromebook
- How to Calculate Taxes on Overtime Pay
- VPN Not Working on iPhone? Fixes That Actually Work
- Hide & Unhide Apps on Samsung Phones
- Fix DNS Server Unavailable Error in Windows 11
- Fix iOS 17 Keyboard Not Working Properly