sodcalculator

10 Tech How-To

How to Install New Windows and Flash Them

Guide 10-56678 · Updated · Step by step

This guide walks you through installing a new window and properly flashing it to prevent water damage and air leaks. You’ll learn the correct order for the sill pan, flashing tape, and house wrap, plus how to set the window level and plumb. Before starting, measure the rough opening and confirm the new window is the right size and type for your wall assembly.

What You’ll Need

  • Replacement window (with nailing flange)
  • Flashing tape (self-adhered, 4-inch or 6-inch wide)
  • Sill pan (or flexible sill flashing membrane)
  • Shims (cedar or plastic)
  • Galvanized or stainless steel roofing nails or screws
  • Cordless drill/driver
  • Utility knife
  • Caulk gun and exterior-grade sealant
  • Level (at least 24 inches)
  • Tape measure
  • Pry bar and hammer (for old window removal)
  • Safety glasses and work gloves
  • House wrap tape (if repairing torn building wrap)

Step-by-Step

  1. Remove the old window. Carefully pry off interior trim, then cut any nails holding the exterior flange. Lift the old unit out. If the window is nailed through the frame, use a reciprocating saw to cut the nails.
  2. Inspect and prep the rough opening. Check that the framing is square and free of rot. Replace any damaged wood. Clean the sill and jambs of old caulk, debris, and dust. The opening should be about 1/2 inch larger than the window on all sides.
  3. Install a sill pan. Cut a piece of flexible sill flashing or use a pre-formed pan. Center it on the sill, extending up the jambs about 4 inches. Fold the sides up to create a dam. Secure with staples or nails near the outer edge. This catches any water that gets past the window.
  4. Apply flashing tape to the sill. Cut a piece of flashing tape long enough to cover the sill and extend 6 inches up each jamb. Press it firmly over the sill pan, smoothing out bubbles. The tape should lap over the sill pan’s back edge.
  5. Set the window in the opening. With help, lift the window into place. Rest it on the sill, centered left to right. Check that the flange sits flat against the sheathing.
  6. Shim and level the window. Place shims under the sill at the corners and center. Use a level to adjust until the sill is level side to side. Then check the jambs for plumb (vertical) and adjust shims behind them. The window must be square and not twisted.
  7. Nail the window flange. Starting at the top corner, drive nails through the flange into the framing, about 6 inches apart. Do not overdrive – the flange should be snug but not deformed. Work from the top down, alternating sides. Leave the bottom flange for now.
  8. Apply bottom flashing tape. Cut a piece of tape that spans the sill and extends up the jambs. Press it over the bottom flange, covering the nail heads. This is the first layer of the shingle-style flashing.
  9. Flash the side jambs. Cut two pieces of tape, each about 12 inches longer than the window height. Apply one to each side, covering the flange and extending onto the sheathing. Start at the bottom and work up, overlapping the bottom tape. The tape should cover the side nails.
  10. Flash the top. Cut a piece of tape that covers the top flange and extends a few inches beyond the corners. Apply it over the top flange. It should overlap the side tapes at the corners.
  11. Integrate with house wrap. If the house wrap is intact, pull it down over the top flashing tape and tape it. If the wrap is damaged, patch it with house wrap tape. The key is that water runs down the wrap, over the top tape, then over the side tapes, then the bottom tape – never behind.
  12. Seal the gaps. Apply a bead of exterior sealant between the window frame and the rough opening on the outside, if required by the window manufacturer. Some windows use backer rod and sealant instead of tape.
  13. Finish interior. Add insulation around the jambs (use low-expanding foam), then reinstall interior trim. Check the window operates smoothly.

Common Mistakes

  • Flashing order wrong. The top tape must overlap the side tapes, and the side tapes must overlap the bottom tape. If you reverse this, water can get behind.
  • Skipping the sill pan. A pan is your last defense against water that gets past the window. Without it, water sits on the wood sill and rots it.
  • Over-nailing. Driving nails too hard deforms the flange, creating gaps. Use a nail gun with depth adjustment or stop before the head sinks.
  • Not leveling. A window that’s out of level will not operate correctly and may cause glass stress.
  • Using the wrong tape. Regular duct tape or masking tape will fail. Use self-adhered flashing tape designed for windows.

Tips

  • Work on a dry day with temperatures above 40°F (4°C) for best tape adhesion.
  • Clean the sheathing with a brush before applying tape – dust kills adhesion.
  • Use a roller or press firmly along the tape edges to ensure a watertight seal.
  • If your window has a built-in nailing fin, follow the manufacturer’s flashing instructions – they may differ slightly.
  • For brick or stucco exteriors, you’ll need additional steps like a drip cap and possibly a masonry saw. Consult a pro.

Troubleshooting

  • Water leaks after installation. Check the flashing overlaps – water should never see a seam facing upward. Re-tape any suspect areas. Also verify the sill pan is sloped slightly outward.
  • Window won’t open or close. The frame is likely racked (not square). Remove the window, re-shim, and re-check level and plumb before nailing.
  • Condensation between panes. This is a sealed-unit failure, not an installation issue. The window will need to be replaced under warranty.
  • Air drafts around the window. The gap between frame and rough opening may not be sealed. Use low-expanding foam on the interior, but avoid overfilling – it can bow the frame.
  • Flashing tape won’t stick. The surface is too cold or dirty. Warm the tape with a heat gun (on low) and clean the surface with a solvent like isopropyl alcohol.

Frequently Asked Questions

Do I need to use a sill pan?

Yes, for most installations. A sill pan catches any water that penetrates the window and directs it outside. It’s a low-cost insurance against rot.

Can I use caulk instead of flashing tape?

No. Caulk is not a substitute for flashing. Flashing tape is designed to shed water and remains flexible. Caulk can crack and fail over time.

What’s the difference between a nail fin and a block frame window?

A nail fin (or nailing flange) is a thin metal or vinyl lip that extends around the window and is nailed to the sheathing. Block frame windows are inserted into a finished opening and secured with screws – they don’t have a flange, so flashing is done differently.

How long does it take to install one window?

For a first-timer, plan on 2-4 hours per window, including prep and cleanup. With experience, it can be done in about 1 hour.

Do I need to remove the old window’s exterior trim?

Usually yes, to access the flange. If the trim is in good shape, you can sometimes remove it carefully and reinstall it. But if it’s rotted, replace it.

Can I install a window myself?

Yes, if you’re comfortable with basic carpentry and have a helper. The most important parts are accurate measuring, leveling, and proper flashing. If you’re unsure about any step, hire a professional – a poorly installed window can cause serious water damage.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →