sodcalculator

10 Tech How-To

Draft Dodger for Doors and Windows: DIY Guide

Guide 10-51840 · Updated · Step by step

Draft dodgers, also known as draft stoppers or snakes, are fabric tubes filled with insulating material that block cold air from sneaking in under doors and windows. This simple DIY project can make a room noticeably warmer in winter and cooler in summer, reduce your energy bills, and cut down on noise and dust. Before you start, decide which doors or windows you want to cover and measure their width. The guide below walks you through making a basic fabric tube, filling it, and finishing it so it fits snugly.

What You’ll Need

  • Fabric: cotton, flannel, or an old towel. You’ll need a piece about 2–3 inches wider than your door/window and about 10–12 inches tall (for a standard door gap).
  • Filling: dried beans, rice, polyester fiberfill, old towels, or crumpled newspaper. You’ll need about 2–3 cups per foot of length.
  • Thread and needle, or a sewing machine.
  • Scissors or rotary cutter.
  • Measuring tape.
  • Straight pins or clips.
  • Funnel (optional, for pouring filling).
  • Iron (optional, for crisp seams).

Step-by-Step

  1. Measure your door or window. Use the measuring tape to find the exact width of the opening you want to block. For a door, measure from one side of the frame to the other at the floor. For a window, measure the width of the sill. Add 2–3 inches to this measurement for seam allowance and a snug fit.
  2. Cut the fabric. Cut a rectangle that is your adjusted width by about 10–12 inches tall. For example, for a 36-inch door, cut a piece 39 inches wide and 11 inches tall. If you want a longer, thinner snake, adjust the height (e.g., 8 inches for a thinner one).
  3. Fold the fabric in half lengthwise. Right sides together, fold the fabric so the two short ends meet. Pin the edges together, leaving one short end open.
  4. Sew the long edge and one short edge. Using a ½-inch seam allowance, sew along the long open side and across one short end. Backstitch at the start and end to secure the stitches. If you don’t have a machine, use a simple running stitch with a needle and thread.
  5. Turn the tube right side out. Carefully pull the fabric through the open end so the sewn seams are on the inside. Use a pencil or chopstick to push out the corners neatly.
  6. Fill the tube. Pour your filling into the open end. A funnel helps. For a firmer draft blocker, use beans or rice; for a softer one, use fiberfill or old towels. Fill it about 80–90% full—leave some slack so it can bend and conform to the gap.
  7. Sew the open end closed. Fold the raw edges of the open end inward by about ½ inch and pin. Sew across the opening, using a blind stitch or a simple whip stitch by hand, or a straight stitch on the machine.
  8. Test the fit. Place the draft dodger along the base of the door or on the window sill. It should sit flush against the surface and block the gap completely. Adjust the position if needed.

Common Mistakes

  • Cutting the fabric too short. If you don’t add the extra 2–3 inches, the draft dodger may be too short to cover the entire gap, leaving cold air to sneak around the ends.
  • Overfilling. A too-tight tube won’t lie flat and may leave gaps at the corners. Leave a little give.
  • Using a fabric that’s too thin. Lightweight fabric can tear under the weight of heavy fillings like beans. Choose a medium-weight cotton or use a double layer.
  • Sewing the open end shut before turning. Remember to leave one short end open; otherwise, you’ll have to undo stitches.
  • Not measuring the actual gap. Door gaps vary; a draft dodger that’s too thin won’t block a wide gap. Measure the height of the gap and adjust the tube’s diameter accordingly.

Tips

  • Add a handle. Sew a fabric loop or attach a small button to one end so you can easily move the draft dodger when you need to open the door.
  • Make it washable. Use a removable cover: sew a separate outer sleeve with a zipper or Velcro, and fill an inner fabric bag. This way, you can wash the cover without removing the filling.
  • Use a non-slip bottom. Attach a few dots of hot glue or a strip of rubber shelf liner to the bottom to keep it from sliding.
  • For windows, make a longer, thinner snake. Window sills are often wider than door gaps, so a flat, wide tube works better. You can also make two shorter ones and place them side by side.
  • Decorate with fabric. Choose a fabric that matches your room or use a fun pattern to make the draft stopper a design feature.

Troubleshooting

  • Draft still coming through. Check that the tube is long enough to cover the entire width. Also, make sure it’s thick enough to fill the gap—add more filling if needed. For doors, the tube should sit directly against the floor and the door bottom.
  • Fabric rips at the seams. This often happens if the filling is too heavy or the seam allowance is too small. Reinforce the seams by sewing them twice, or use a stronger fabric like denim or canvas.
  • The draft dodger slides out of place. Add a non-slip backing or make it slightly longer so it wedges between the door frame and the wall. You can also attach a small weight (like a bag of sand) inside the ends.
  • Filling leaks out. If you used beans or rice, make sure the seams are tightly sewn and the fabric is tightly woven. Double-stitch the ends, and consider using a fabric with a tight weave to prevent small particles from escaping.
  • It’s too stiff to bend around corners. For odd-shaped gaps, use a softer filling like fiberfill or old t-shirts. You can also make the tube in two sections and join them with a fabric hinge.

Frequently Asked Questions

What is the best filling for a draft dodger?

The best filling depends on your needs. Dried beans or rice give a heavy, firm weight that stays put, but they can be hard and may not conform perfectly to uneven gaps. Polyester fiberfill is soft and flexible but lighter. Old towels or fabric scraps are a good middle ground—they’re dense enough to block air but still pliable.

How long should a draft dodger be?

It should be slightly longer than the width of the door or window opening, typically 2–3 inches longer. This ensures it covers the entire gap and can be tucked into the corners for a snug fit.

Can I use a draft dodger on a window that opens?

Yes, but you’ll need to remove it before opening the window. Place it on the sill directly against the bottom sash. For sliding windows, place it on the track where the two sashes meet.

How do I clean a draft dodger?

If you made a removable cover, unzip it and wash the cover in cold water. If the filling is inside a permanent cover, spot-clean with a damp cloth. Avoid machine washing the whole thing, as beans or rice can swell and ruin the fabric.

Will a draft dodger really save energy?

Yes, by blocking cold air infiltration, they reduce the amount of heat that escapes, so your heating system doesn’t have to work as hard. The effect is modest but noticeable, especially in older homes with drafty doors.

Can I make a draft dodger without sewing?

Yes, you can use fabric glue or iron-on hem tape to seal the edges. For a no-sew version, cut a rectangle of fabric, fold it in half, and glue the long edge and one short end. Turn it right side out, fill, and glue the last end shut. Let the glue dry completely before using.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →