sodcalculator

10 Tech How-To

Shokz Pairing Guide & Bluetooth Fixes

Guide 10-56519 · Updated · Step by step

This guide walks you through pairing Shokz bone-conduction headphones with your phone, computer, or other Bluetooth device, and covers the most common connection problems and how to fix them. You will learn the correct pairing procedure for both new and already-paired Shokz models, plus practical steps to resolve dropped audio, one-sided sound, and devices that refuse to connect.

What You’ll Need

  • Your Shokz headphones (fully charged or with at least some battery)
  • The Bluetooth device you want to connect to (phone, tablet, computer, etc.)
  • Access to the Bluetooth settings menu on that device
  • For multi-device models: a second device if you plan to pair two at once

Step-by-Step

Pairing Shokz Headphones for the First Time

  1. Charge your Shokz: Plug them into a USB charger using the included cable. Wait until the LED indicator shows a solid or blinking light (usually red or blue) to ensure enough battery for pairing. A completely dead battery can prevent pairing.
  2. Turn off the headphones: If they are on, press and hold the multifunction (power) button until the LED light turns off. This ensures a clean start for pairing mode.
  3. Enter pairing mode: Press and hold the multifunction button for about 5 to 7 seconds. You will hear a voice prompt saying “pairing” and the LED indicator will start blinking red and blue alternately. This means the headphones are now discoverable.
  4. Open Bluetooth settings on your device: On your phone, tablet, or computer, go to the Bluetooth settings menu. Make sure Bluetooth is turned on.
  5. Select your Shokz model: In the list of available devices, look for the name of your specific Shokz model (e.g., OpenRun, OpenFit, OpenMove, Aeropex). Tap or click on it.
  6. Confirm the connection: Your device may ask for a PIN or confirmation code. If prompted, enter 0000 or simply confirm the match. Once connected, you will hear a voice prompt saying “connected” and the LED light will stop blinking.
  7. Test the audio: Play some music or a video to confirm sound is coming through both earpieces.

Pairing a Second Device (Multi-Point)

Many Shokz models support connecting to two devices at once, like a phone and a laptop.

  1. Pair the first device normally using the steps above.
  2. Turn off Bluetooth on the first device after pairing is complete.
  3. Put the headphones back into pairing mode: Turn them off, then press and hold the multifunction button for 5-7 seconds until the LED blinks red and blue.
  4. Pair the second device from its Bluetooth settings.
  5. Re-enable Bluetooth on the first device: The headphones should automatically reconnect to the first device. Now both are connected, and audio will switch based on which device plays sound.

Reconnecting After Power Off

  1. Turn on the headphones: Press the multifunction button once. They will automatically try to reconnect to the last paired device(s).
  2. If they don’t reconnect: Open the Bluetooth settings on your device and tap the Shokz name to manually reconnect.

Common Mistakes

  • Not entering pairing mode properly: Holding the button too short (1-2 seconds) turns the headphones on/off instead of entering pairing mode. You need the full 5-7 seconds until you hear “pairing”.
  • Pairing while already connected to another device: If the headphones are actively connected to a phone, they may not appear in pairing mode on a second device. Turn off Bluetooth on the connected device first.
  • Forgetting to remove old pairings: If your Shokz are paired to 10+ old devices, they can become confused. Reset the pairing list (see Troubleshooting) to clear old connections.
  • Using the wrong button: The volume buttons do not control pairing. Only the multifunction (power) button works for pairing.
  • Ignoring device-side Bluetooth cache: If your phone has a corrupted Bluetooth cache, it may not find the headphones even when they are in pairing mode. Clearing the cache (in phone settings) often fixes this.

Tips

  • Keep firmware updated: Use the Shokz app (available for iOS and Android) to check for and install firmware updates. Updates often fix Bluetooth stability issues.
  • Stay within range: Bluetooth works best within 10 meters (33 feet) of the source device. Walls and metal objects can reduce this range significantly.
  • Reduce interference: Wi-Fi routers, microwaves, and other Bluetooth devices can cause interference. Move away from them if you experience stuttering.
  • Charge regularly: Low battery can cause audio dropouts and connection instability. Keep your Shokz charged above 20% for reliable performance.
  • Reset the headphones periodically: If you experience recurring connection issues, perform a factory reset (see Troubleshooting) once a month to clear any accumulated glitches.

Troubleshooting

Headphones Not Showing Up in Bluetooth List

  1. Make sure the headphones are in pairing mode (LED blinking red/blue).
  2. Turn off Bluetooth on your device, wait 10 seconds, then turn it back on.
  3. Restart your phone or computer.
  4. If still not found, reset the headphones: turn them off, then press and hold the multifunction button for 10-15 seconds until the LED flashes red (or you hear a specific prompt). This clears the pairing list. Then re-enter pairing mode and try again.

Audio Keeps Dropping or Stuttering

  1. Move closer to the source device and remove any obstacles between them.
  2. Turn off Wi-Fi on your device temporarily to see if interference stops.
  3. Check the battery level on the headphones – low battery causes dropouts.
  4. Unpair and re-pair the headphones completely (delete from device, re-enter pairing mode, connect again).
  5. Update firmware via the Shokz app.

Only One Side Has Sound

  1. Check the audio balance settings on your device – make sure it’s centered.
  2. Clean the ear tips and the area around the speaker with a dry cloth. Wax or debris can block sound.
  3. Test with a different audio source to rule out the headphone itself.
  4. If the issue persists on all devices, the headphone may have a hardware fault – contact Shokz support for warranty service.

Headphones Connect but No Sound

  1. Check the volume on both the headphones and the source device – press the volume up button on the Shokz.
  2. Make sure the correct output device is selected on your computer (some systems have multiple audio outputs).
  3. Restart the audio app you are using.
  4. Unpair and re-pair the headphones.

Can’t Connect to a Second Device

  1. Disconnect the first device (turn off its Bluetooth) before pairing the second.
  2. Make sure your Shokz model supports multi-point (not all do – check the manual).
  3. Reset the headphones to clear all pairings, then pair both devices fresh.

Factory Reset Instructions (General)

  1. Turn off the headphones.
  2. Press and hold the multifunction button for about 10 seconds until the LED flashes red (or you hear a voice prompt).
  3. Release the button. The headphones are now reset and will enter pairing mode automatically.
  4. Re-pair with your device(s) as if they were new.

Frequently Asked Questions

How do I put my Shokz in pairing mode?

Turn the headphones off, then press and hold the multifunction button for 5-7 seconds until you hear “pairing” and the LED blinks red and blue.

Why won’t my Shokz connect to my iPhone?

Ensure the headphones are in pairing mode, then go to Settings > Bluetooth on your iPhone and tap the Shokz name. If they don’t appear, restart your iPhone and try again. Also check that the headphones are not already connected to another device.

Can I connect my Shokz to two devices at once?

Yes, most newer models (OpenRun, OpenFit, OpenMove) support multi-point. Pair the first device, then turn off its Bluetooth, pair the second, then re-enable the first. Audio switches automatically.

How do I reset my Shokz headphones?

Turn them off, then press and hold the multifunction button for about 10 seconds until the LED flashes red. This clears all paired devices and returns to factory settings.

Why does the sound cut out when I turn my head?

This is usually caused by Bluetooth signal blockage. Keep the source device on the same side as the headphones’ antenna (usually the right earpiece) and avoid covering the earpiece with a hat or thick hair.

Do Shokz work with Windows computers?

Yes. Put the headphones in pairing mode, then go to Windows Settings > Devices > Bluetooth & other devices, click “Add Bluetooth or other device,” select Bluetooth, and choose your Shokz model.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →