sodcalculator

10 Tech How-To

How to Remove Router Bit on Craftsman Router

Guide 10-46670 · Updated · Step by step

Removing a router bit from a Craftsman router is a routine maintenance task that every woodworker needs to know. Whether you’re switching to a different profile or replacing a dull bit, doing it correctly prevents damage to the tool and keeps you safe. This guide walks you through the exact steps for both fixed-base and plunge-base Craftsman routers, including how to handle stuck bits and common pitfalls.

What You’ll Need

  • Router wrench (usually included with the router, often a 3/4-inch or 1-1/8-inch open-end wrench)
  • Second wrench (for the spindle lock, if your model uses two wrenches)
  • Safety glasses
  • Work gloves (optional but recommended)
  • Soft cloth or brush (to clean the collet and shaft)
  • Penetrating oil (like WD-40) for stuck bits

Step-by-Step

  1. Unplug the router. This is non-negotiable. Even if the switch is off, unplugging ensures no accidental start. For cordless models, remove the battery.
  2. Remove any accessories. If you have a router table, edge guide, or dust collection attachment, remove them to access the collet area freely.
  3. Identify the collet type. Most Craftsman routers use a standard ER-type collet (like ER20 or ER32) or a proprietary collet with a nut. Check the manual if unsure. The collet nut is the large hex or knurled piece at the bottom of the spindle.
  4. Engage the spindle lock. Look for a button or lever near the base of the router. Press it or rotate it to lock the spindle. You’ll feel it click into place. If your model doesn’t have a spindle lock, you’ll need two wrenches: one to hold the spindle shaft (often flat spots on the shaft) and one to turn the collet nut.
  5. Position the wrenches. Place the router wrench on the collet nut. If using two wrenches, place the second on the spindle flats. The wrenches should be oriented so that turning the collet nut counterclockwise (when viewed from the bottom) loosens it.
  6. Loosen the collet nut. Turn the wrench counterclockwise. It should turn relatively easily—maybe half a turn to a full turn. Do not force it. If it doesn’t budge, see Troubleshooting below.
  7. Remove the bit. Once the collet nut is loose, the bit should slide out freely. If it doesn’t, gently twist the bit while pulling downward. Never pull on the cutting edges with your bare hand; use a cloth or gloves.
  8. Clean the collet and shaft. Wipe off any sawdust, resin, or debris from the collet, the collet nut threads, and the bit shank. A clean collet ensures proper grip and prevents future stuck bits.
  9. Store the bit safely. Place the bit in a case or wrap it in a cloth to protect the cutting edges.

Common Mistakes

  • Forgetting to unplug: The most dangerous mistake. Always unplug first.
  • Turning the wrench the wrong way: A common error. The collet nut is right-hand threaded, so you must turn it counterclockwise to loosen. If you turn it clockwise, you’ll tighten it further.
  • Using the wrong wrench size: A loose-fitting wrench can slip and round off the nut. Use the correct size and ensure it’s fully seated.
  • Forcing the bit out: Yanking on a stuck bit can damage the collet or the bit. Use penetrating oil and patience.
  • Not cleaning before reinserting: Leaving debris in the collet can cause the bit to seat improperly, leading to runout or the bit being thrown.

Tips

  • Use the spindle lock properly: Make sure the spindle lock is fully engaged. If it slips, the spindle will rotate with the wrench, making it impossible to loosen.
  • Keep the collet clean: After every few uses, remove the collet and clean it with a brush and some solvent. This prevents rust and resin buildup.
  • Don’t over-tighten: When you put a new bit in, tighten the collet nut firmly but not with excessive force. Over-tightening can distort the collet and make removal difficult later.
  • Use a bit extractor: If you have a severely stuck bit, a router bit extractor tool can grip the shank and help twist it out without damaging the collet.
  • Consider a quick-release collet: Some aftermarket collets allow tool-free bit changes. While not necessary, they can save time if you switch bits frequently.

Troubleshooting

Bit won’t loosen: If the collet nut won’t turn, apply a few drops of penetrating oil around the collet nut and the shaft. Let it sit for 10-15 minutes. Then try again. If it still won’t budge, tap the wrench handle gently with a mallet to break the corrosion or resin bond. Do not use excessive force, as you could damage the spindle.

Spindle lock won’t engage: If the spindle lock button doesn’t click in, the spindle may be misaligned. Rotate the collet nut slightly by hand until the lock engages. If it’s still stuck, check for debris blocking the lock mechanism.

Bit is stuck in the collet: After loosening the nut, the bit may still be stuck due to resin or rust. Gently tap the bit shank upward with a soft mallet while holding the router. If that fails, use a bit extractor or apply heat (with a heat gun) to the collet nut area to expand it slightly—be careful not to overheat plastic parts.

Collet nut is rounded: If the nut’s corners are worn, a standard wrench won’t grip. Use a pipe wrench or a collet nut socket designed for rounded nuts. Replace the nut if it’s too damaged.

Wrench slips: Clean the wrench and nut with a degreaser to improve grip. Ensure the wrench is the correct size and fully seated.

Frequently Asked Questions

Q: Do all Craftsman routers have a spindle lock?
A: Most modern Craftsman routers have a spindle lock button, but some older models may not. If yours doesn’t, use two wrenches: one on the spindle shaft flats and one on the collet nut.

Q: What size wrench do I need for my Craftsman router?
A: It varies by model. Common sizes are 3/4-inch, 1-1/8-inch, or 1-1/4-inch. Check your manual or measure the collet nut across the flats. The wrench that came with the router is the safest bet.

Q: Can I remove the bit without a wrench?
A: No. The collet nut is tightened to a specific torque, and you need a wrench to loosen it. Using pliers or other tools can damage the nut.

Q: Why is my bit stuck even after loosening the nut?
A: This is usually due to resin buildup or rust on the bit shank or inside the collet. Apply penetrating oil and let it sit. Gently tap the bit upward with a mallet. If it’s still stuck, use a bit extractor.

Q: How often should I clean the collet?
A: Ideally, after every few hours of use, especially if you’re cutting resinous woods like pine. A quick wipe-down with a cloth and some solvent keeps the collet functioning smoothly.

Q: Can I use a regular socket wrench on the collet nut?
A: Only if you have the correct size socket and it’s deep enough to fit over the collet. Many collet nuts are hex-shaped, so a socket can work, but the included wrench is designed to fit properly without slipping.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →