This guide walks you through resetting an ASUS BIOS the right way, covering three related tasks: restoring default settings, clearing the CMOS (which also resets BIOS passwords), and removing a forgotten BIOS password. You’ll learn the safest order to do these, what each method actually does, and how to avoid common pitfalls that can leave your system unbootable or your data at risk.
What You’ll Need
- Your ASUS motherboard or laptop model number (printed on the board or in the system info).
- A Phillips-head screwdriver (for desktop CMOS jumper or battery removal).
- An anti-static wrist strap or a metal object to touch (to ground yourself).
- A small flat-head screwdriver or a jumper cap (for the CMOS jumper).
- A CR2032 coin cell battery (only if you plan to replace it).
- Access to the motherboard manual (PDF from ASUS support) for exact jumper/battery location.
Step-by-Step
- Back up your current BIOS settings (if possible). Boot into the BIOS (press Del or F2 repeatedly during startup). Use the Save & Exit tab and select Save as Profile to store your current settings to a USB drive. This is not strictly necessary, but it saves you from reconfiguring everything manually.
- Try the in-BIOS reset first. In the BIOS, go to the Exit or Save & Exit tab and select Load Optimized Defaults (or Restore Defaults). Confirm when prompted. Then select Save Changes & Reset. This resets all settings to factory defaults without touching the CMOS hardware.
- If you need a full CMOS clear (e.g., for a forgotten password or a system that won’t POST), power down completely. Shut down Windows, then switch off the power supply (if a desktop) or unplug the laptop. Wait 30 seconds.
- Open the case (desktop) or remove the bottom panel (laptop). For a desktop, remove the side panel. For a laptop, remove the bottom cover (check the manual for the exact screws). Ground yourself by touching a metal part of the chassis.
- Locate the CMOS jumper or battery. On most ASUS desktop boards, there is a two-pin jumper labeled CLR_CMOS or CLRTC. On laptops, the CMOS battery is usually a small round CR2032 coin cell. If you can’t find it, consult the manual.
- Clear the CMOS using the jumper (desktop). With the power off, move the jumper cap from pins 1-2 to pins 2-3 (or press the onboard CLR_CMOS button if your board has one). Hold it in the clear position for 5-10 seconds. Then move it back to the original position.
- Clear the CMOS using the battery (desktop or laptop). Gently pry the battery out of its holder using a flat-head screwdriver. Wait 5-10 minutes (or press the power button for 15 seconds with the battery out to drain residual charge). Reinsert the battery with the + side facing up.
- Reassemble and power on. Close the case, reconnect power, and turn on the system. You may see a message like “CMOS checksum error – Defaults loaded”. Press F1 to enter the BIOS and reconfigure your settings (date/time, boot order, fan curves, etc.).
- For a forgotten BIOS password, the CMOS clear above usually removes it. If the password is still requested after the clear, try the Backdoor method: enter a wrong password three times, then type in a specific code that appears on screen (e.g., “A-1234”). This code is unique to your board; you can look it up online or contact ASUS support with that code to get the master password.
- If you have an ASUS laptop with a soldered CMOS battery, use the reset hole. Many ASUS laptops have a tiny pinhole on the bottom or side labeled RST or CMOS. Insert a paperclip into the hole for 10 seconds while the laptop is off and unplugged.
Common Mistakes
- Not unplugging the power supply. Even with the switch off, the PSU can still supply standby power. Always unplug the AC cord before touching internal components.
- Leaving the jumper in the clear position. If you forget to move it back, the system will keep resetting on every boot and may not start.
- Shorting the wrong pins. Only short the two pins designated for CMOS clear. Shorting other pins can damage the board.
- Using the reset button on the case instead of the motherboard jumper. The case reset button does not clear CMOS; it only restarts the system.
- Not waiting long enough after removing the battery. Residual charge in capacitors can keep the CMOS memory alive. Wait at least 5 minutes, or press the power button to drain.
- Assuming the password is gone after a soft reset. A simple “Load Optimized Defaults” does not clear a BIOS password. You need a full CMOS clear.
Tips
- Before clearing, note your current BIOS version. After a reset, the version stays the same, but you may need to re-enable XMP/DOCP for your RAM speed.
- Use a profile save. If you have a stable overclock, save it as a profile so you can restore it after a reset.
- For laptops, remove the battery and the CMOS battery. Some ASUS laptops have a separate internal battery that can keep the CMOS powered. Disconnect both if possible.
- If you have a desktop with a CLR_CMOS button on the I/O panel, use that. It’s the easiest and safest method – just press it while the system is off.
- After reset, update your BIOS to the latest version. ASUS often improves stability and compatibility with updates. Check the support page for your model.
Troubleshooting
- System won’t POST after clearing. This is usually normal – the BIOS is reinitializing. Wait a few seconds. If it still doesn’t POST, try a different RAM slot or reseat the RAM. Also check that the CPU fan is connected.
- You see a black screen with a cursor. This can be a sign of a corrupted BIOS. Try the “BIOS Flashback” feature on your ASUS board (if supported) – plug a USB with the BIOS file into the designated port and press the Flashback button.
- Password still appears after CMOS clear. Some laptops store the password in a separate EEPROM chip. You may need to use the backdoor code or contact ASUS support with the code displayed after 3 failed attempts.
- CMOS checksum error every boot. This means the CMOS battery is dead or the clear didn’t fully complete. Replace the battery with a new CR2032.
- Boot loop after reset. This often happens if your RAM overclock profile (XMP) was lost. Enter the BIOS and re-enable XMP, or manually set the RAM voltage and timings.
- If you can’t find the CMOS jumper or battery, check the manual. Some ASUS boards have a CLR_CMOS pad on the bottom edge that requires shorting with a screwdriver. Never guess – wrong shorting can fry the board.
Frequently Asked Questions
- Will clearing CMOS delete my Windows installation? No. It only resets BIOS settings, not data on your hard drive or SSD.
- How often should I clear CMOS? Only when you have a specific problem like a boot failure, unstable overclock, or forgotten password. It’s not a routine maintenance step.
- What is the difference between “Load Optimized Defaults” and clearing CMOS? The former resets settings to factory defaults but leaves the CMOS memory intact. The latter physically erases the CMOS memory, which also removes passwords and any custom settings.
- Can I clear CMOS without opening the case? Yes, if your ASUS motherboard has a CLR_CMOS button on the rear I/O panel. Otherwise, you must open the case.
- Does clearing CMOS reset the BIOS version? No, the BIOS firmware version stays the same. Only the settings are reset.
- My laptop has a non-removable CMOS battery. What do I do? Look for a reset pinhole on the bottom. If none exists, use the BIOS backdoor code method or contact ASUS support.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- How to Enable Privacy Indicators on Chromebook
- How to Calculate Taxes on Overtime Pay
- VPN Not Working on iPhone? Fixes That Actually Work
- Hide & Unhide Apps on Samsung Phones
- Fix DNS Server Unavailable Error in Windows 11
- Fix iOS 17 Keyboard Not Working Properly