sodcalculator

10 Tech How-To

How to Restore a Pitted Chrome Faucet

Guide 10-49304 · Updated · Step by step

Chrome faucets develop pits when the protective chromium layer is damaged, exposing the underlying brass or zinc to moisture and corrosion. This guide shows you how to clean, fill, and refinish those pits so the surface looks smooth and shiny again. You will need a few supplies and about an hour of work, and the result will last for years if you apply the topcoat correctly.

What You’ll Need

  • Mild dish soap and a soft cloth
  • Fine steel wool (0000 grade) or a fine abrasive pad
  • Isopropyl alcohol (70% or higher)
  • Automotive body filler (e.g., Bondo) or a metal repair epoxy
  • Plastic spreader or putty knife
  • Fine-grit sandpaper (400, 800, 1200, 2000 grit)
  • Rubbing compound (automotive grade)
  • Chrome spray paint (specifically for metal, with a clear coat)
  • Masking tape and plastic sheeting (to protect the sink and counter)
  • Clean, lint-free cloths
  • Optional: small artist brush for precision filler application

Step-by-Step

  1. Clean the faucet thoroughly. Wash the entire faucet with mild dish soap and warm water to remove grease, soap scum, and debris. Rinse well and dry completely with a soft cloth.
  2. Assess the damage. Inspect the pits closely. Small pits (less than 1/8 inch) can be filled and painted. Larger areas of corrosion may require replacing the faucet, as the base metal may be too compromised.
  3. Sand the pitted areas. Use 400-grit sandpaper to lightly sand the pits and the surrounding chrome. This removes loose chrome and creates a rough surface for the filler to adhere to. Be gentle—you only need to scuff the surface, not cut deep into the metal.
  4. Clean the sanded areas. Wipe away all sanding dust with a clean, dry cloth. Then, use isopropyl alcohol on a lint-free cloth to degrease the sanded spots. Let the alcohol evaporate completely.
  5. Apply the filler. Mix the automotive body filler or epoxy according to the manufacturer’s instructions. Use a plastic spreader to press the filler into each pit, overfilling slightly to allow for sanding. For very small pits, a toothpick or artist brush can help apply the filler precisely.
  6. Let the filler cure. Allow the filler to harden completely. Curing time varies by product—check the label, but typically it’s 30–60 minutes for body filler, or overnight for epoxy.
  7. Sand the filler smooth. Start with 400-grit sandpaper to level the filler with the surrounding chrome. Then move to 800, 1200, and finally 2000-grit, always sanding in a circular motion with light pressure. The surface should feel perfectly smooth when you run your finger across it.
  8. Clean and mask the faucet. Wipe away all sanding dust, then clean with alcohol again. Use masking tape and plastic sheeting to protect the sink, counter, and any areas of the faucet you don’t want to paint.
  9. Apply the chrome spray paint. Shake the can well. Hold it 6–8 inches from the surface and apply several thin, even coats, waiting 10–15 minutes between coats. Let the paint dry completely (usually 1–2 hours).
  10. Apply the clear coat. Once the chrome paint is dry to the touch, spray a clear protective topcoat (also in thin coats) to seal the paint and add durability. Let it cure fully—ideally 24 hours before regular use.
  11. Buff to a shine. After the clear coat has cured, use a rubbing compound and a soft cloth to buff the repaired areas to a glossy finish that blends with the rest of the faucet.

Common Mistakes

  • Skipping the sanding step. Filler won’t stick to shiny chrome. Always scuff the surface first.
  • Applying filler too thick. Thick layers shrink as they cure and can crack. Build up in thin layers if needed.
  • Using regular paint instead of metal spray paint. Standard paint won’t adhere well to chrome and will peel quickly.
  • Not masking properly. Overspray on the sink or counter is hard to remove. Take time to cover everything.
  • Rushing the curing times. If you paint over filler that hasn’t fully cured, it will sink and crack.

Tips

  • For tiny pits, you can skip the filler and just sand lightly, then paint—the paint will fill micro-scratches.
  • Work in a well-ventilated area and wear a mask to avoid inhaling fumes from the filler and paint.
  • If the faucet is heavily pitted across a large area, consider replacing it. Refinishing is best for localized damage.
  • After refinishing, avoid abrasive cleaners and scrub pads on the repaired area to extend the life of the finish.
  • Test the spray paint on a scrap piece of metal first to ensure the color matches your faucet’s chrome.

Troubleshooting

  • Filler won’t stick or keeps falling out. The surface wasn’t clean or sanded enough. Sand again, clean with alcohol, and reapply.
  • Paint looks dull or blotchy. You may have applied too thick a coat, or the can was too far away. Sand the area lightly with 2000-grit, clean, and apply thinner coats.
  • Repaired area is still visible after painting. The filler wasn’t sanded perfectly smooth. Sand again with 2000-grit, clean, and reapply paint.
  • Paint peels off after a few weeks. The surface wasn’t properly degreased, or you didn’t use a clear coat. Strip the paint, clean thoroughly, and reapply with primer and clear coat.
  • Rust reappears under the paint. You missed some corrosion. Sand down to bare metal, treat with a rust converter, and redo the filler and paint.

Frequently Asked Questions

Can I restore a pitted chrome faucet without repainting?

No. Once the chrome is pitted, the protective layer is gone. Filling the pits and repainting is the only way to restore a smooth surface. Polishing alone won’t remove pits.

Will the repair match the rest of the faucet?

With careful color matching and buffing, the repair can be nearly invisible. However, if the faucet has a brushed or satin finish, matching the texture is harder. Chrome spray paint is usually glossy, so it works best on polished chrome.

How long will the repair last?

If you use quality materials and apply a clear coat, the repair can last 1–3 years with normal use. Harsh cleaners or abrasive scrubbing will shorten its life.

Is it cheaper to repair or replace the faucet?

Repairing costs about $20–$40 for supplies, while a new chrome faucet starts around $50–$100. If the damage is extensive, replacement may be more cost-effective and reliable.

Can I use nail polish or enamel paint instead of chrome spray paint?

Nail polish isn’t durable enough for a faucet that gets wet frequently. Enamel paint can work, but it’s harder to apply evenly. Chrome spray paint is specifically formulated for metal and gives the best finish.

Do I need to remove the faucet to repair it?

No. You can repair it in place. Just mask the surrounding area carefully to avoid overspray. However, if you can remove the faucet, it’s easier to work on and you can spray it more evenly.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →