This guide shows you how to turn on Bluetooth on your iPhone, either from the Control Center for a quick toggle or through the Settings app for more control. You’ll also learn how to connect a device, avoid common mistakes, and fix issues when Bluetooth won’t turn on.
What You’ll Need
- An iPhone running iOS 11 or later (the steps are the same for newer versions)
- The Bluetooth device you want to connect (headphones, speaker, keyboard, etc.)
- That device charged and in pairing mode (check its manual for how to enter pairing mode)
Step-by-Step
- Unlock your iPhone. Press the Side button or use Face ID / Touch ID to get to the Home Screen.
- Open Control Center.
- On an iPhone with Face ID: swipe down from the top-right corner of the screen.
- On an iPhone with a Home button: swipe up from the bottom edge of the screen.
- Tap the Bluetooth icon. It looks like a stylized “B” made of two triangles. When Bluetooth is off, the icon is gray. When you tap it, it should turn blue or white (depending on your iOS version) to show it’s on.
- Check the icon color. A blue (or white) icon means Bluetooth is now enabled. If it turns gray again immediately, see the Troubleshooting section below.
- Connect a device (optional). If you want to pair a new device, go to Settings > Bluetooth and make sure the toggle at the top is green. Then look under “Other Devices” and tap the name of your device when it appears.
- Confirm the connection. Once paired, your device will appear under “My Devices” with the word “Connected” below it. The Bluetooth icon in the status bar (if shown) will also indicate an active connection.
Common Mistakes
- Turning off Bluetooth from Control Center doesn’t fully disable it. On newer iPhones, tapping the Control Center toggle only disconnects current devices until the next day. To truly turn off Bluetooth, go to Settings > Bluetooth and toggle it off there.
- Forgetting to put the accessory in pairing mode. Most devices need a button press or a specific sequence to become discoverable. If it doesn’t show up, check the device’s manual.
- Assuming the icon means “on” when it’s gray. A gray icon means Bluetooth is off. A blue or white icon means it’s on. Some iOS versions show a white icon when on.
- Not checking battery levels. If your accessory has low battery, it may not connect or may disconnect quickly. Check the battery widget or the Bluetooth settings page.
Tips
- Use Siri: You can say “Hey Siri, turn on Bluetooth” and it will do it for you, but you’ll still need to confirm on the screen if you’re using Control Center only.
- Keep devices close: Bluetooth range is about 30 feet (10 meters). Walls and obstructions can reduce that.
- Forget and re-pair: If a device is acting up, go to Settings > Bluetooth, tap the “i” next to the device, then tap “Forget This Device.” Then pair it again from scratch.
- Check the status bar: If you don’t see the Bluetooth icon, you can enable it in Settings > Control Center > Customize Controls (though the icon in the status bar only appears when a device is connected).
- Update iOS: Keeping your iPhone updated can fix Bluetooth bugs. Go to Settings > General > Software Update.
Troubleshooting
Bluetooth won’t turn on (toggle is gray or immediately turns off):
- Restart your iPhone. Press and hold the Side button and either volume button until the power off slider appears. Slide to power off, wait 30 seconds, then turn it back on.
- Check for a stuck button. Make sure no buttons are pressed down, especially the volume or side buttons.
- Reset network settings. Go to Settings > General > Transfer or Reset iPhone > Reset > Reset Network Settings. This will clear all saved Wi-Fi and Bluetooth connections, so you’ll need to re-pair devices afterward.
- Check for hardware damage. If Bluetooth still won’t turn on after a reset, it may be a hardware issue. Contact Apple Support or visit an Apple Store.
Bluetooth is on but no devices appear:
- Make sure the accessory is in pairing mode (often a light blinking rapidly).
- Turn the accessory off and on again.
- Move closer to the accessory.
- If the accessory is already paired, it may be connected to another phone. Disconnect it from that phone first.
Device connects but keeps dropping:
- Check battery levels on both the iPhone and the accessory.
- Remove obstacles between them.
- Forget the device and re-pair it.
- Restart both the iPhone and the accessory.
Frequently Asked Questions
Q: Does turning on Bluetooth drain my battery?
A: Yes, but very little. Modern Bluetooth Low Energy (BLE) devices use minimal power. If you’re not using any Bluetooth accessories, you can turn it off to save a tiny amount of battery.
Q: Why does my Bluetooth turn off by itself?
A: If you turned it off via Control Center, it will automatically turn back on the next day. If it turns off immediately, it may be a temporary glitch—try restarting your iPhone or resetting network settings.
Q: Can I connect multiple Bluetooth devices at once?
A: Yes, iPhones can connect to multiple devices simultaneously, but audio output is usually limited to one device at a time (unless you use AirPlay 2 for speakers).
Q: How do I know if a device is connected?
A: Go to Settings > Bluetooth. Under “My Devices,” the connected device will show “Connected” in gray text. You may also see the Bluetooth icon in the status bar.
Q: What does “Not Connected” mean under a device?
A: It means the device is paired (saved) but not currently active. Tap the device name to try connecting, or make sure it’s powered on and in range.
Q: Why can’t I see my AirPods in the Bluetooth list?
A: AirPods appear in the Bluetooth list only when they are in pairing mode (press and hold the button on the back of the case). Otherwise, they show up in the AirPods menu when you open the case near your iPhone.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Fix Error 0x8007025d in Windows 10
- Fix Alexa App Stuck on Setup
- Android Camera for 7 Office Tasks: Step-by-Step
- Pair Phone to Pioneer Stereo After Bluetooth Reset
- Fix Windows Not Saving Remote Desktop Credentials
- Essential Tips for macOS Users Switching to Windows