Unrooting your Samsung Galaxy Grand Max restores the phone to its original factory state, which lets you install official system updates, use banking and streaming apps that block rooted devices, and get warranty service if needed. This guide covers two reliable methods: using the SuperSU app to fully unroot, and flashing the stock firmware with Odin for a completely clean system. Before starting, back up anything important, fully charge the phone, and ensure you have a Windows PC and a USB cable.
What You’ll Need
- Samsung Galaxy Grand Max (SM-G7200 or SM-G7202 model)
- Windows PC or laptop
- Original USB cable for the phone
- SuperSU app installed (if using Method 1)
- Odin flashing tool (version 3.10.7 or newer)
- Stock firmware file for your exact model and region
- Samsung USB drivers installed on the PC
Step-by-Step
Method 1: Unroot with SuperSU (Simplest)
- Open the SuperSU app on your Galaxy Grand Max.
- Go to the Settings tab inside the app.
- Scroll down to the Cleanup section and tap Full unroot.
- Read the warning that appears and tap Continue.
- Allow the app to restore the original boot image and remove the su binary. This takes a minute or two.
- When prompted, tap Reboot to restart the phone.
- After reboot, check that the SuperSU icon is gone. If it remains, install a root checker app from the Play Store to confirm root access is removed.
Method 2: Flash Stock Firmware with Odin (Thorough)
- Download the correct stock firmware for your exact model number (SM-G7200 or SM-G7202) and your region. Use sites like SamMobile or SamFirm, and verify the build matches your current Android version.
- Extract the downloaded firmware ZIP file. You should get a file ending in
.tar.md5. - Extract the Odin ZIP file and run
Odin3.exeas administrator. - Power off the Galaxy Grand Max completely.
- Boot into Download Mode: press and hold Volume Down + Home + Power together for about 10 seconds, then press Volume Up when the warning screen appears.
- Connect the phone to your PC with the USB cable. Odin should show a blue or yellow box in the ID:COM section saying “Added!”.
- In Odin, click the AP button (or PDA in older versions) and select the
.tar.md5firmware file. Do not touch any other buttons. - Make sure only F. Reset Time and Auto Reboot are checked in the Options tab. Do not enable Re-Partition.
- Click Start and wait. The process takes 5-10 minutes. When it finishes, Odin shows a green PASS! message and the phone reboots automatically.
- If the phone does not reboot, unplug it and hold Power for 10 seconds to turn it on manually.
- Once booted, set up the phone as new. Root access is now completely gone, and the stock recovery is restored.
Common Mistakes
- Using the wrong firmware – Flashing a firmware for a different model or region can brick the phone. Always verify the exact model number under Settings > About Phone.
- Enabling Re-Partition in Odin – This option can corrupt the partition layout and make the phone unbootable. Leave it unchecked unless you are following a specific repartition guide.
- Interrupting the flash – Unplugging the USB cable or closing Odin mid-flash can permanently damage the device. Be patient.
- Skipping the backup – Flashing stock firmware wipes all data. If you did not back up, you lose everything.
- Using a cheap or damaged USB cable – A poor connection can cause the flash to fail or the phone to disconnect. Use the original cable.
Tips
- Before starting Method 2, disable any antivirus or Windows Defender real-time protection temporarily, as they can interfere with Odin.
- Keep the phone plugged in during the entire process. If the battery dies mid-flash, the phone may be unrecoverable.
- After unrooting, wipe the cache partition from stock recovery (Volume Up + Home + Power, then select “Wipe cache partition”) to clear any leftover root data.
- If you plan to root again later, note that flashing stock firmware removes the custom recovery (like TWRP) as well.
- Check for OTA updates after unrooting – if one appears, the unroot was successful.
Troubleshooting
- Odin does not detect the phone – Reinstall Samsung USB drivers, try a different USB port (preferably USB 2.0), and ensure you are in Download Mode. Restart the PC and try again.
- Odin gets stuck at “SetupConnection” – Close Odin, unplug the phone, reboot both devices, and try again. Also check that Kies or Smart Switch is not running in the background.
- Flash fails with a red “FAIL!” message – The firmware file may be corrupted or wrong. Re-download it and verify the model number. Also try a different Odin version.
- Phone boots into a boot loop after flashing – Boot into recovery (Volume Up + Home + Power) and perform a factory reset. If that fails, flash the firmware again with a fresh download.
- SuperSU “Full unroot” says it failed – Reboot the phone and try again. If it still fails, use Method 2 to flash stock firmware instead.
- Root checker still shows root after Method 1 – Some system apps may remain. Use a file manager to delete any leftover files like
/system/app/Superuser.apk, or just use Method 2 for a clean slate.
Frequently Asked Questions
Will unrooting erase my data?
Method 1 (SuperSU) keeps your data intact. Method 2 (Odin flash) wipes everything because it restores the full system partition. Always back up before using Odin.
Can I unroot without a PC?
Yes, if you have SuperSU installed, the “Full unroot” option works entirely on the phone. However, if you removed SuperSU or it fails, you will need a PC for the Odin method.
Will unrooting restore my warranty?
Flashing stock firmware restores the software to factory condition, which usually satisfies warranty checks. However, if the bootloader counter shows “Custom” or “0x1” (KNOX warranty void), some service centers may still refuse. Check your KNOX status by booting into Download Mode.
What is KNOX and does unrooting fix it?
KNOX is Samsung’s security framework. Rooting trips a permanent eFuse that sets the warranty bit to 0x1. Unrooting does not reset this bit – it stays tripped forever. This only matters for Samsung warranty claims, not for normal phone use.
Can I receive OTA updates after unrooting?
Yes, once you are on stock firmware with root removed, OTA updates should work normally. If you only used Method 1, occasionally a leftover root file blocks updates – in that case, use Method 2.
What if I want to root again later?
You can re-root using the same method you originally used (e.g., CF-Auto-Root or TWRP + Magisk). Unrooting does not permanently lock the bootloader on the Grand Max.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Fix msmpeg2vdec.dll Errors in Windows
- How to Update Sonos App and Speakers
- Unlock iPad Without Apple ID: Is It Possible?
- iOS 18 WhatsApp Notifications Not Working? Fix
- Fix Windows Cannot Locate Suitable Printer Driver
- How to Group Text and Pictures in Word