sodcalculator

10 Tech How-To

iPhone Stuck on White Apple Logo After iOS 10 Upgrade

Guide 10-48662 · Updated · Step by step

If your iPhone is stuck on the white Apple logo after an iOS 10 upgrade, the most likely cause is a failed or interrupted software update, and the fix usually involves force restarting the device or restoring it via a computer. This article explains why this happens, what you can try at home, and when you need professional help.

Why Does This Happen?

An iPhone shows the Apple logo during startup and while installing a software update. The logo stays on screen while the system verifies and applies the new firmware. If the update is interrupted—by a power loss, a faulty download, or insufficient storage—the phone can get stuck in a loop where it can’t finish booting. iOS 10, released in 2016, was a major update that changed the file system and added many new features, which increased the chance of update-related glitches on older devices. However, the same basic troubleshooting steps apply to any iOS version.

First Try: Force Restart

A force restart doesn’t erase your data. It simply cuts power to the phone and reboots it, which can clear a temporary software hang. The method depends on your iPhone model:

  • iPhone 8 or later: Press and quickly release the Volume Up button, then the Volume Down button. Press and hold the Side button until the Apple logo appears, then release.
  • iPhone 7 and iPhone 7 Plus: Press and hold both the Side button and the Volume Down button for at least 10 seconds, until the Apple logo appears.
  • iPhone 6s and earlier, including iPhone SE (1st gen): Press and hold both the Home button and the Side (or Top) button for at least 10 seconds.

If the logo reappears and then the phone boots normally, you’re done. If it stays stuck on the logo, move to the next step.

Recovery Mode and DFU Mode

When a force restart doesn’t work, your iPhone may need to be restored through a computer. Recovery Mode is a built-in diagnostic state that lets you update or restore the phone’s software. DFU (Device Firmware Update) Mode is a deeper level that bypasses the bootloader and is used when Recovery Mode fails. Both will erase your data if you choose “Restore,” so only use them if you have a backup or you’re prepared to lose everything.

To enter Recovery Mode:

  1. Connect your iPhone to a computer with the latest version of iTunes (or Finder on macOS Catalina or later).
  2. Force restart your iPhone, but don’t release the buttons when the Apple logo appears—keep holding until you see the “Connect to computer” screen.
  3. On the computer, a dialog will appear offering to Update or Restore. Try “Update” first—it keeps your data. If that fails, you’ll need to “Restore.”

To enter DFU Mode: The exact button sequence varies by model, but generally you connect the phone, then hold the Side and Volume Down buttons (iPhone 7) or Side and Home (older models) for a few seconds, release the Side button while keeping the other held, and wait for a black screen. The computer will detect the device in DFU mode. If you’re not sure you did it right, just use Recovery Mode—it’s safer and easier.

What If You Don’t Have a Backup?

If you never backed up your iPhone, a restore will wipe everything. However, your photos, contacts, and messages might still be recoverable if you had iCloud Backup enabled. Check iCloud.com to see what’s there. If you have no backup, you can try third-party data recovery software, but it’s not guaranteed to work and can be expensive. The safest approach is to always keep an up-to-date backup, either to iCloud or to a computer.

Common Mistakes and Misconceptions

One common mistake is trying to update over a weak Wi-Fi connection or with low battery. Always plug your iPhone into power and use a stable network before updating. Another misconception is that a stuck Apple logo means the hardware is broken—in most cases it’s a software issue that a restore can fix. However, if you’ve tried multiple restores and the phone still won’t boot, the problem could be a failing storage chip or other hardware fault, which requires professional repair.

When to Seek Professional Help

If you’ve tried force restart, Recovery Mode, and DFU restore, and the phone still won’t boot, it’s time to contact Apple Support or visit an Apple Store. They have diagnostic tools that can identify hardware issues. If your iPhone is under warranty or covered by AppleCare+, the repair may be free. Otherwise, you’ll have to pay for out-of-warranty service, which can cost more than the phone’s current value for older models. In that case, it might be more economical to buy a new device.

Frequently Asked Questions

Will a force restart erase my data?

No, a force restart just reboots the phone. It doesn’t delete any of your photos, messages, or apps. It’s the first thing to try because it’s safe and often works.

How long should I wait on the Apple logo before trying something else?

Give it at least 15-20 minutes. A major update like iOS 10 can take a while to apply, especially on older devices. If it’s still stuck after that, then try a force restart.

Can I fix a stuck Apple logo without a computer?

Sometimes, a force restart is enough. If it’s not, you’ll need a computer to restore the phone. There’s no way to reinstall iOS directly from the phone itself when it won’t boot.

What’s the difference between Recovery Mode and DFU Mode?

Recovery Mode loads a basic interface that allows iTunes to communicate with the phone. DFU Mode bypasses the bootloader entirely, so the phone can accept firmware even if the bootloader is corrupted. DFU is more powerful but also riskier—if you do it wrong, you might end up in a worse state. Stick with Recovery Mode first.

Is there any way to recover data from a phone stuck on the Apple logo?

If you have a backup, yes. If not, you can try third-party recovery tools, but they’re not guaranteed to work and may cost money. Your best bet is to always back up regularly.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →