If your Samsung Galaxy Buds aren’t charging, the fix is usually simple: clean the charging contacts, check the cable and case battery, and reset the buds. This article walks through the most common causes and step-by-step solutions for both the Galaxy Buds and their charging case.
Why Galaxy Buds Stop Charging
The Galaxy Buds charge through metal contacts on the underside of each earbud that connect to pogo pins inside the case. When those contacts get dirty or the buds aren’t seated correctly, charging fails. The case itself charges wirelessly or via USB-C, and a depleted case battery is another common culprit. Software glitches can also interrupt the connection between the buds and the case.
Clean the Charging Contacts
Earwax, dust, and lint are the number one reason Galaxy Buds stop charging. Over time, residue builds up on the gold contacts on the buds and the pins in the case, creating a barrier that blocks the electrical connection.
- Remove the earbuds from the case.
- Use a dry, soft-bristled brush (like a clean toothbrush) to gently scrub the gold contacts on the bottom of each bud.
- Dip a cotton swab in isopropyl alcohol (70% or higher) and wring it out so it’s barely damp. Gently rub the pogo pins inside the case.
- Let everything dry completely for 10–15 minutes before putting the buds back in.
Do not use water or submerge the buds. If the contacts are deeply corroded, you may need to repeat the cleaning a few times. This fix resolves the issue in the majority of cases.
Check the Charging Case Battery
The case itself can run out of power, especially if you haven’t charged it in a while. If the case battery is completely dead, the buds won’t charge even when they’re seated properly.
- Plug the case into a charger using the USB-C cable that came with it (or any compatible USB-C cable).
- Alternatively, place the case on a Qi wireless charging pad. Make sure the case is centered on the pad.
- Wait at least 15 minutes before checking if the buds start charging. The case may be in a low-power state and need time to wake up.
- Check the LED on the front of the case. Red or orange means it’s charging; green means it’s full.
If the case doesn’t respond at all, try a different cable and wall adapter. Some third-party cables are power-only and don’t support the data pins needed for charging.
Reseat the Earbuds in the Case
A surprisingly common issue is that the earbuds aren’t sitting flush in the charging slots. The magnets should pull them into place, but a misaligned wingtip or ear tip can prevent proper contact.
- Remove both earbuds from the case.
- Check that the ear tips and wingtips are firmly attached and not blocking the charging contacts.
- Place each earbud back in its slot, aligning the L and R markings.
- Press down gently until you feel the magnet click.
- Close the lid and wait a few seconds. The LED should blink to indicate charging.
If the LED doesn’t blink, the contacts aren’t connecting. Repeat the cleaning step and try again.
Reset the Galaxy Buds
Sometimes the issue is software-related. A reset can clear minor glitches that prevent the buds from recognizing the case or charging properly.
- Put the earbuds in the case and close the lid.
- Open the Galaxy Wearable app on your phone.
- Go to Earbuds settings → Reset → Reset earbuds.
- Confirm the reset. The buds will disconnect and reboot.
- Reconnect them to your phone as if they were new.
Note that this resets your custom equalizer settings and touch controls. If you can’t use the app, you can also try forgetting the buds in your phone’s Bluetooth settings and re-pairing them.
Update Firmware and Check the Wearable App
Samsung periodically releases firmware updates for Galaxy Buds that fix charging bugs and improve battery management. If your buds are not charging consistently, an outdated firmware could be the cause.
- Open the Galaxy Wearable app on your phone.
- Check for a Firmware update option under Earbuds settings.
- If an update is available, download and install it while the buds are in the case with the lid closed.
- Keep the case charged above 50% during the update.
Also, check the app’s battery indicator for each bud and the case. If the app shows one bud at 0% and the other at 100%, the issue is likely the contacts or the battery itself.
When to Consider Battery Replacement
If you’ve cleaned the contacts, checked the case, reset the buds, and updated the firmware, but the buds still won’t charge, the internal battery may have degraded. Lithium-ion batteries lose capacity over time, especially after hundreds of charge cycles. This is more likely if your buds are more than two years old.
In that case, you have a few options:
- Contact Samsung support or visit an authorized service center for a battery replacement.
- Check if your buds are still under warranty (typically one year from purchase).
- Consider buying a replacement pair if the cost of repair is close to the price of new buds.
There’s no safe way to replace the battery yourself without specialized tools, and opening the case can damage the water-resistant seals.
Frequently Asked Questions
Why is only one Galaxy Bud charging?
This usually means the other bud’s contacts are dirty or it’s not seated properly. Clean both buds and the case pins, then reseat them. If only one bud still won’t charge, its battery may be faulty.
Can I charge Galaxy Buds without the case?
No, the Galaxy Buds require the case to charge. There is no wired or wireless charging port on the buds themselves. The case acts as the charging cradle and power bank.
How long does it take to charge Galaxy Buds?
Charging times vary by model. Generally, a 15-minute charge gives about an hour of playback, and a full charge takes about 1–2 hours. The case itself takes about 2–3 hours to fully charge via USB-C or wireless.
Can I use any wireless charger for my Galaxy Buds case?
Yes, any Qi-certified wireless charger should work. However, the case must be centered on the pad, and some chargers may be too weak to charge through thick cases. If you have a thick protective case on the Buds case, remove it.
Why does my Galaxy Buds case show a red light but won’t charge the buds?
A red light on the case usually means the case battery is low. If it stays red while plugged in, the case may not be getting power. Try a different cable and adapter, and clean the USB-C port on the case. If the port is damaged, the case may need repair.
Will a factory reset delete my saved Bluetooth pairings?
Yes, a reset will remove the buds from your phone’s paired devices. You’ll need to re-pair them. It also resets your touch controls and equalizer settings to default.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Fix Error 0x8007025d in Windows 10
- Fix Alexa App Stuck on Setup
- Android Camera for 7 Office Tasks: Step-by-Step
- Pair Phone to Pioneer Stereo After Bluetooth Reset
- Fix Windows Not Saving Remote Desktop Credentials
- Essential Tips for macOS Users Switching to Windows