If your windows won’t stay up, the counterbalance system is failing—usually worn springs, a broken sash cord, or a dirty track. You can often repair this yourself in under an hour with basic tools and a few inexpensive parts.
How Window Balance Systems Work
Most double-hung and single-hung windows use a hidden counterweight to offset the sash’s weight, letting it stay put at any height. The two common systems are:
- Weight-and-pulley: Old windows have cast-iron weights inside the frame, connected to the sash by a rope or chain over a pulley.
- Spring balances: Newer windows use a coiled spring inside a channel or a block-and-tackle mechanism that pulls against the sash.
When the counterbalance breaks or loses tension, the sash becomes heavier than the counterforce and slides down. Dirt, paint, or swollen wood can also cause friction that makes the sash feel stuck or fall.
Quick Fixes to Try First
Before taking anything apart, try these simple checks—they solve a surprising number of cases:
- Clean the tracks: Use a stiff brush and a vacuum to remove dust, cobwebs, and paint chips. Then wipe with a damp cloth and dry.
- Lubricate the tracks: Apply a silicone spray or a dry Teflon lubricant to the channels. Avoid oil-based products that attract dirt.
- Check for paint lock: If the window is painted shut, run a utility knife along the seam between the sash and the frame to break the seal.
- Tighten screws: On the balance shoe (the part that rides in the track), tighten any loose screws with a screwdriver.
If the window still won’t stay up after cleaning and lubricating, the counterbalance itself is likely the problem.
Repairing a Spring Balance Window
Spring balances are common in vinyl, aluminum, and newer wood windows. The repair varies slightly by brand, but the general steps are:
- Remove the sash: Lift the window fully, then tilt it inward (most have a tilt latch). If it won’t tilt, pry the stop molding off carefully with a flat bar.
- Locate the balance: You’ll see a metal tube or block in the track. Some have a visible spring; others are sealed.
- Replace the balance: Unhook the balance from the sash and the frame, then install a new one of the same size and weight rating. Most hardware stores sell universal replacements.
- Reinstall the sash: Hook the balance onto the sash, tilt it back into place, and test the lift.
If the balance is a spiral type, you may need to adjust the tension by turning the top hook with a screwdriver. Check the manufacturer’s instructions for your specific window.
Repairing a Weight-and-Pulley Window
These classic windows have a rope or chain that can fray, snap, or detach. To fix:
- Remove the stop molding on one side using a pry bar and a putty knife to avoid damage.
- Pull out the lower sash and set it aside.
- Access the weight pocket—a small door on the side of the frame. Open it and remove the old weight.
- Replace the cord: Thread a new sash cord (or chain) over the pulley, tie it to the weight, and then tie the other end to the sash. The weight should be about half the sash’s weight for proper balance.
- Reinstall the sash and replace the stop molding.
This job takes about an hour per window. If the rope is intact but the window still falls, the weight may be missing or the wrong size.
How to Choose the Right Replacement
When buying a new spring balance, you need three numbers:
- Length: Measure the balance from end to end when fully extended.
- Weight rating: Weigh the sash on a bathroom scale. The balance should be rated for that weight (or slightly higher).
- Type: Note whether it’s a block-and-tackle, spiral, or constant-force spring. Bring the old one to the store if possible.
For weight-and-pulley windows, buy sash cord or chain that matches the old one’s diameter. Chain is more durable but can be noisier.
Common Mistakes and Misconceptions
A frequent error is assuming the window needs replacing when a simple balance swap would fix it. Another is over-lubricating—too much oil attracts dust and makes the window sticky.
People also mistake a sticking window for a balance problem. If the window is hard to lift but stays up once raised, the issue is friction, not the counterbalance. In that case, cleaning and waxing the tracks is the right fix.
Finally, never force a stuck window. You can break the glass or damage the frame. Work slowly and use a pry bar only on the stop molding, never on the glass.
Cost and When to Call a Pro
Replacement spring balances cost roughly $5–$20 each, and sash cords are a few dollars. If you do the labor yourself, the total is usually under $50 per window.
Call a professional if:
- The window frame is rotting or warped.
- You have a custom or historic window with unusual dimensions.
- You’re uncomfortable removing the sash or working with the weight pocket.
A pro can also rebalance the window if the weights are mismatched, which is a more involved job.
Frequently Asked Questions
How do I know if my window has a spring balance or weights?
Look at the track. If you see a metal tube or a visible spring, it’s a spring balance. If you see a rope or chain going over a pulley, it’s a weight-and-pulley system. You can also check by removing the stop molding—the weight pocket is a dead giveaway.
Can I fix a window that won’t stay up without replacing anything?
Sometimes. If the sash cord is just off the pulley, you can reattach it. If the spring balance has a tension adjustment, you can tighten it. But if the spring is broken or the cord is frayed, replacement is the only reliable fix.
Why does my window stay up in the summer but falls in the winter?
Wood windows expand and contract with humidity. In humid summer air, the sash may swell and create more friction, which can hold it up. In dry winter air, the sash shrinks and becomes lighter relative to the balance, so it falls. This is a sign the balance is weak and needs replacing.
Is it safe to use a screwdriver to hold the window up temporarily?
Yes, as a temporary measure. Drive a screw or nail through the track above the sash to keep it from falling. But this can damage the track, so only use it until you can do a proper repair.
Can I replace a spring balance with a different type?
You can, but it’s easier to match the existing type. If you switch from a block-and-tackle to a spiral, you may need to drill new holes and adjust the mounting. For most people, buying the same type is the simplest and most reliable choice.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- How to Remove or Insert a SIM Card in Your iPhone
- How to Send a Fax from Android or iOS
- Outlook Stuck on Loading Profile? Fix It
- MacBook Trackpad Protection: A Complete Guide
- PlayStation Overheating: Causes & Fixes
- Error 0x803f7001 Windows: Fixes & Meaning