sodcalculator

10 Tech How-To

BSD vs Linux: Key Differences Explained

Tag 10-52995 · Updated · Standard formula, shown below

Volume 9.26 yd³
Volume
250.0 ft³
Result
Lawn length
40 ft
You entered
Lawn width
25 ft
You entered
You enter
Lawn length, Lawn width, Depth
You get
Volume, Volume
Rounding
2 dp · 1 dp

The main difference between BSD and Linux is that BSD is a complete operating system developed as a whole, while Linux is just a kernel that is combined with GNU tools and other software to form a full OS. This fundamental distinction affects how each system is developed, licensed, and used in practice.

Formula

The calculator above estimates the volume of soil, compost, or other material needed to cover a rectangular lawn or garden bed. The formula is:

Volume (yd³) = Length (ft) × Width (ft) × Depth (in) ÷ 324

Where:

  • Length – the longer side of the area, in feet
  • Width – the shorter side of the area, in feet
  • Depth – how deep the material will be spread, in inches
  • 324 – conversion factor (1 cubic yard = 27 cubic feet, and 1 foot = 12 inches, so 27 × 12 = 324)

The second output gives the same volume in cubic feet, which is useful when buying material in smaller bags.

Worked Example

Using the default values from the calculator: length = 40 ft, width = 25 ft, depth = 3 in.

  1. Convert depth to feet: 3 in ÷ 12 = 0.25 ft
  2. Calculate volume in cubic feet: 40 × 25 × 0.25 = 250 ft³
  3. Convert to cubic yards: 250 ÷ 27 = 9.26 yd³

The calculator shows 9.26 yd³ (rounded to 2 decimals) and 250 ft³, matching the manual calculation.

When to Use This Calculator

Use this tool when planning any landscaping project that involves adding a layer of material over a rectangular area:

  • Topsoil for a new lawn
  • Compost or mulch for a garden bed
  • Sand or gravel for a base layer
  • Fill dirt for leveling a yard

The result tells you how much bulk material to order. For bagged products, divide the cubic feet result by the bag volume (e.g., 0.75 ft³ per bag) and round up to the nearest whole bag.

How to Read the Result

The primary answer is in cubic yards, the standard unit for bulk deliveries. A typical dump truck holds about 10–14 cubic yards. The cubic feet figure is more useful for smaller quantities bought in bags. Remember that settling and compaction will reduce the final depth, so it is often wise to order 5–10% extra.

Common Mistakes

  • Mixing units – Always enter length and width in feet, depth in inches. If you measure in meters, convert first (1 m = 3.281 ft).
  • Forgetting the depth conversion – Dividing by 324 only works when depth is in inches. If you enter depth in feet, divide by 27 instead.
  • Rounding too early – Keep full precision until the final answer to avoid errors.
  • Ignoring waste – For irregular shapes, add 10% or more to your order.

Limitations of the Formula

This calculator assumes a perfectly rectangular area with uniform depth. Real lawns have curves, slopes, and varying thicknesses. For irregular shapes, break the area into rectangles and sum the results. The formula also does not account for compaction – fresh soil settles after watering, so the final depth may be slightly less than planned.

Frequently Asked Questions

How many cubic feet are in a cubic yard?

There are 27 cubic feet in one cubic yard (3 ft × 3 ft × 3 ft). This is why the conversion factor in the formula is 324 (27 × 12) when depth is in inches.

Should I order extra material?

Yes, it is generally recommended to order 5–10% more than the calculated volume. This covers spillage, uneven spreading, and settlement after watering or rain.

Can I use this for mulch in a circular bed?

No, this calculator is for rectangular areas. For a circle, use the formula π × r² × depth, then convert to cubic yards (divide by 27 if depth is in feet, or by 324 if depth is in inches).

How do I convert the result to metric?

One cubic yard equals approximately 0.7646 cubic meters. Multiply the cubic yard result by 0.7646 to get cubic meters. For liters, multiply cubic meters by 1000.

What depth of topsoil do I need for a new lawn?

For most grass types, 4–6 inches of topsoil is recommended. This calculator defaults to 3 inches, which is suitable for adding a thin layer over existing soil, but adjust the depth input to match your project.

Related

Formula used
in l | Lawn length | ft | 40 | 0 | 100000
in w | Lawn width | ft | 25 | 0 | 100000
in d | Depth | in | 3 | 0 | 120
out yd | Volume | yd³ | l * w * d / 324 | 2
out ft3 | Volume | ft³ | l * w * d / 12 | 1

Each line is one input (in, sel, list) or one result (out: label, unit, formula, decimals). How the calculators work

Method: the standard formula for this calculation, rounded as each result states. See how the calculators work or report an error.

More in this bed

The whole Tech How-To bed →