sodcalculator

10 Tech How-To

Fix AirPods Pro Touch Controls Not Working

Guide 10-44552 · Updated · Step by step

If your AirPods Pro touch controls have stopped responding, the fix usually involves cleaning the stems, re-pairing the earbuds, or adjusting the pressure sensor settings in iOS. Below is a step-by-step troubleshooting guide that covers the most common causes and solutions, from simple software checks to hardware-related issues.

How AirPods Pro Touch Controls Work

AirPods Pro (1st and 2nd generation) use a force sensor located in the small, flat indentation on each stem. Unlike older AirPods that relied on tapping the outer surface, the Pro models respond to a deliberate squeeze. The sensor detects both the amount of pressure and the duration of the squeeze, so a light tap or a quick pinch may not register. Each earbud can be configured independently in iOS to control noise cancellation, Siri, or playback. If the sensor is blocked, dirty, or the software is glitched, the controls will appear unresponsive even though the earbuds still play audio.

Quick Fixes to Try First

Before diving into deeper troubleshooting, try these simple steps—they resolve a surprising number of cases:

  • Remove and reinsert the earbuds – sometimes the sensor just needs a fresh contact with your ear.
  • Check the battery – low battery can cause erratic behavior; place them in the case for a few minutes.
  • Restart your iPhone or iPad – a temporary Bluetooth glitch often clears after a reboot.
  • Turn off and on Bluetooth – go to Settings > Bluetooth, toggle it off, wait 5 seconds, then turn it back on.
  • Reset the AirPods Pro – put them in the case, close the lid, wait 30 seconds, then reopen and hold the button on the back of the case until the LED flashes amber, then white. Re-pair them to your device.

Clean the Stems and Sensor Area

Dirt, earwax, or moisture on the stem can interfere with the force sensor. Use a dry, soft, lint-free cloth to gently wipe the entire stem, especially the concave area where the sensor sits. Do not use water, cleaning solutions, or sharp objects—they can damage the microphone mesh or the sensor itself. If you’ve been exercising, sweat residue can also build up; dry the stems thoroughly before using the controls again. For stubborn grime, slightly dampen the cloth with fresh water (wring it out well) and wipe carefully, then dry completely.

Check and Adjust Touch Control Settings

Sometimes the controls are working but not set to the action you expect. Go to Settings > Bluetooth, tap the “i” icon next to your AirPods Pro, and verify the settings:

  • Left and Right: Choose what a squeeze does—e.g., “Noise Control” or “Siri.” If set to “Off,” squeezing won’t do anything.
  • Press and Hold: Make sure the duration is set to “Short” or “Medium” if you find the default too long.
  • Noise Control: If you selected “Noise Control,” confirm that at least one mode (ANC, Transparency, Off) is enabled. If all are off, the squeeze will have no effect.

Also, on iOS 17 and later, you can adjust the “Press and Hold” speed under Accessibility > AirPods to make the sensor more responsive.

Update Firmware and iOS

Outdated firmware on the AirPods Pro or an outdated iOS version can cause touch control bugs. To check the firmware version, go to Settings > Bluetooth > (i) next to your AirPods and look at “Firmware Version.” There’s no manual update button—firmware updates install automatically when the AirPods are in the case, charging, and near your iPhone. Ensure your iPhone is updated to the latest iOS version and keep the AirPods case connected to power overnight. If a known bug exists, Apple typically releases a fix within a few weeks.

Hardware Issues and When to Seek Repair

If you’ve tried all the above and the touch controls still don’t respond, the force sensor may be physically damaged. Common causes include dropping the earbuds, exposure to water (even though they are water-resistant, not waterproof), or wear over time. Before assuming the worst, test the controls on another device (e.g., an iPad or another iPhone) to rule out a phone-specific issue. If they fail on all devices, the sensor is likely faulty. Check if your AirPods Pro are still under Apple’s limited warranty or AppleCare+; if so, contact Apple Support or visit an Apple Store for service. Out-of-warranty repairs are possible but may cost almost as much as a new pair, so weigh the options.

Frequently Asked Questions

Why do my AirPods Pro controls only work sometimes?

Intermittent issues usually point to a dirty sensor or a loose fit. Ensure the stems are clean and that you’re squeezing the flat area, not the entire stem. Also, check that the earbuds are seated properly in your ears—if they shift, the sensor may not align with your fingers.

Can I change the touch controls to require less pressure?

Yes, on iOS 17 or later, go to Settings > Accessibility > AirPods and adjust the “Press and Hold” speed to “Slow” or “Slowest.” This makes the sensor more forgiving, though it also increases the time needed to register a squeeze.

What should I do if only one earbud’s controls aren’t working?

First, check that the settings for that specific earbud aren’t set to “Off.” Then clean the stem thoroughly. If the problem persists, reset your AirPods Pro (as described above) and re-pair them. If only one side still fails, it’s likely a hardware issue with that earbud.

Does the volume control work on AirPods Pro?

Yes, on AirPods Pro (2nd generation), you can swipe up or down on the stem to adjust volume. This feature is not available on the 1st generation, which only supports squeezes for noise control and Siri.

Will a factory reset erase my settings?

Yes, resetting your AirPods Pro will clear all custom settings, including the touch control configuration and noise control preferences. You’ll need to set them up again after re-pairing, but your iOS device will remember some settings if you’ve previously synced them via iCloud.

Can I use the touch controls while wearing gloves?

The force sensor works through thin fabric, but thick gloves or mittens may prevent the sensor from detecting the squeeze. Try using a lighter touch or removing the glove for better accuracy.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →