If Windows fails to start and shows an error like “Windows failed to start. A recent hardware or software change might have caused the issue,” the fix usually involves using the Windows Recovery Environment to run startup repair, restore system files, or revert recent changes. This article explains the most common causes and provides step-by-step solutions you can try before considering a full reinstall.
What Causes the “Windows Failed to Start” Error?
This error typically appears during the boot process, often as a blue screen with the message “Your PC/Device needs to be repaired.” It can be triggered by a variety of issues, including:
- Corrupted system files – essential boot files like
winload.exeor the Boot Configuration Data (BCD) may be damaged. - Failed Windows update – an interrupted or incompatible update can leave the system in an unbootable state.
- Driver or hardware changes – newly installed drivers or hardware that conflicts with Windows.
- Disk errors – bad sectors or file system corruption on the system drive.
- Malware or virus – some infections target boot sectors.
- Power outage or improper shutdown – can interrupt critical writes to the disk.
First Steps: Accessing Windows Recovery Environment
To fix the issue, you need to get into the Windows Recovery Environment (WinRE). If Windows fails to start twice in a row, it should automatically enter WinRE on the third attempt. If not, you can force it by:
- Turning off your PC completely (hold the power button).
- Turning it on and immediately pressing the power button again to turn it off when the Windows logo appears.
- Repeating this process two or three times until you see the “Preparing Automatic Repair” screen.
Alternatively, if you have a Windows installation USB drive, boot from it and select “Repair your computer” on the setup screen.
Solution 1: Run Startup Repair
Startup Repair is the built-in tool that scans for common boot problems and attempts to fix them automatically. It’s the first thing to try because it’s non-destructive and often resolves the issue.
- In WinRE, go to Troubleshoot > Advanced options > Startup Repair.
- Select your operating system (usually Windows 10 or 11).
- Wait for the repair to complete. It may take several minutes and may restart your PC.
If Startup Repair says it couldn’t fix the problem, proceed to the next solution.
Solution 2: Use System Restore
System Restore reverts your system files, settings, and installed programs to an earlier point in time without affecting your personal files. This is especially useful if the error appeared after a recent change.
- In WinRE, go to Troubleshoot > Advanced options > System Restore.
- Choose an account and enter its password.
- Select a restore point that predates the problem (if any are available).
- Follow the prompts to restore your system.
Note: System Restore must be enabled and a restore point must exist. If you don’t see any, skip to the next step.
Solution 3: Rebuild the Boot Configuration Data (BCD)
The BCD stores boot configuration information. If it’s corrupted, Windows won’t start. You can rebuild it using Command Prompt from WinRE.
- In WinRE, go to Troubleshoot > Advanced options > Command Prompt.
- Type the following commands one by one, pressing Enter after each:
bootrec /fixmbr bootrec /fixboot bootrec /scanos bootrec /rebuildbcd
If you get an “Access is denied” error when running bootrec /fixboot, try this alternative:
bcdedit /export C:\BCD_Backup ren C:\boot\BCD BCD.old bootrec /rebuildbcd
After running these, type exit and restart your PC.
Solution 4: Run CHKDSK and SFC
Disk errors or corrupted system files can also prevent boot. Use the following tools to check and repair them.
- Open Command Prompt from WinRE as described above.
- Run
chkdsk /f /r C:(replace C: with your system drive letter if different). This scans for bad sectors and repairs file system errors. It may take a long time. - After CHKDSK completes, run
sfc /scannowto check system file integrity. Note: SFC may not work properly from WinRE; if it fails, you can run it after booting, but if you can’t boot, proceed to the next step.
Solution 5: Uninstall Recent Updates
If the error started after a Windows update, you can uninstall that update from WinRE.
- Go to Troubleshoot > Advanced options > Uninstall Updates.
- Choose “Uninstall latest quality update” or “Uninstall latest feature update” depending on what was recently installed.
- Follow the prompts and restart.
Solution 6: Reset This PC (Keep Files)
If none of the above work, you can reset Windows while keeping your personal files. This reinstalls the OS but removes installed apps and settings.
- In WinRE, go to Troubleshoot > Reset this PC.
- Choose Keep my files.
- Follow the prompts. You may need to provide a Windows installation source (like a USB drive) if the recovery partition is missing.
This is a more drastic step, but it’s less severe than a full reinstall and often fixes the issue.
Frequently Asked Questions
Will these steps delete my files?
Startup Repair, System Restore, BCD rebuild, CHKDSK, and uninstalling updates do not delete personal files. However, System Restore may remove recently installed programs and drivers. Reset This PC with “Keep my files” preserves your personal files but removes apps and settings. Always back up important data if possible, even if you think it’s safe.
What if I don’t have a Windows installation USB?
You can create one using another working computer with the Windows Media Creation Tool from Microsoft’s website. If you can’t create one, try the automatic repair loop method (forcing WinRE by interrupting boot) or use a recovery drive if you previously created one.
Why does the error say “a recent hardware or software change might have caused it”?
Windows shows this generic message when it detects that the boot process failed without a clear cause. It’s not always accurate, but it’s a hint to consider recent changes like new drivers, hardware, or updates that might have corrupted boot files.
Can I fix this without losing my installed programs?
Yes, most solutions (Startup Repair, BCD rebuild, CHKDSK) do not touch your programs. System Restore may remove programs installed after the restore point. Reset This PC removes all apps, but you can reinstall them afterward. If you need to keep everything, try the less invasive fixes first.
What if my PC boots to a black screen instead of the error?
A black screen can indicate a different issue, such as a graphics driver problem or a hardware failure. Try booting into Safe Mode (from WinRE, go to Troubleshoot > Advanced options > Startup Settings > Restart, then press 4 or F4) and uninstall the graphics driver. If the screen remains black, it may be a hardware issue.
Is there a way to prevent this from happening again?
Regularly create restore points, keep your system updated (but wait a few days after a major update to see if issues are reported), avoid abrupt shutdowns, and run periodic disk checks. Also, ensure your antivirus is active and updated to prevent malware that targets boot sectors.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- MacBook Charger Not Working? Fix It Now
- Fix Windows Cannot Be Installed to This Disk
- Zoom on iPhone & iPad: Host or Join a Meeting
- Fix iPhone SE 4 Unable to Activate: Step-by-Step
- Keep Important Emails From Getting Buried in iPhone Mail Categories
- How to Clear RAM on iPhone: Speed It Up