sodcalculator

10 Tech How-To

Attach Router to Ryobi Table Saw: Step-by-Step

Guide 10-55502 · Updated · Step by step

Mounting a router to your Ryobi table saw turns it into a combo machine, letting you use the saw’s fence and table for edge profiling, dadoes, and joinery. This guide walks you through the safe, correct way to attach a standard fixed-base or plunge router to the saw’s extension wing, using a universal router mounting plate. You’ll need a few basic tools and about 30 minutes.

What You’ll Need

  • Ryobi table saw (models with a flat extension wing on the right side)
  • Universal router mounting plate (typically 8″ x 10″ or 9″ x 12″)
  • Fixed-base or plunge router (with a flat base plate)
  • Drill with 3/16″ and 1/8″ bits
  • Jigsaw or router (to cut the hole in the table wing)
  • Router bit (for the test cut)
  • #8 or #10 machine screws, nuts, and washers (usually included with the plate)
  • Wrench or socket set
  • Pencil and straightedge
  • Safety glasses and hearing protection

Step-by-Step

  1. Unplug the table saw. Disconnect the power cord to eliminate any risk of accidental startup.
  2. Remove the existing extension wing. On most Ryobi saws, the right extension wing is held by hex bolts. Use a wrench to remove them and lift the wing off. Set the saw aside.
  3. Trace the mounting plate on the wing. Place the router mounting plate on the wing, centered where you want the router. Trace around it with a pencil.
  4. Mark the router opening. The plate has a large central hole for the router bit. Trace that circle onto the wing as well.
  5. Cut the bit opening. Use a jigsaw or router to cut the central hole. Start with a drill bit to create a starter hole, then cut along the traced circle. Sand the edges smooth.
  6. Drill screw holes in the wing. Place the mounting plate back on the wing, aligned with your trace. Use the plate’s screw holes as a template to mark drill points. Drill 3/16″ holes through the wing.
  7. Attach the mounting plate to the wing. Place the plate on the wing, insert screws from underneath (or from the top, depending on your plate design), and secure with nuts and washers. Tighten firmly, but do not overtighten.
  8. Reattach the wing to the saw. Bolt the wing back onto the saw frame. Ensure it is level with the main table surface. Use a straightedge to check; adjust with shims if needed.
  9. Mount the router to the plate. Remove the router’s base plate (if detachable) and align the router’s screw holes with the plate’s mounting holes. Insert the provided screws and tighten evenly.
  10. Set the router depth. Loosen the router’s depth adjustment, insert a router bit, and set the depth so the bit extends slightly above the table surface. Lock the depth.
  11. Test the setup. Plug in the saw, put on safety glasses, and turn on the router. Make a test cut on a scrap piece of wood, pushing it against the fence and over the bit. Check the cut quality and adjust depth as needed.

Common Mistakes

  • Not leveling the wing: If the wing sits higher or lower than the saw table, the router bit will cut unevenly. Always level it before use.
  • Using the wrong screws: Screws that are too long can poke through the plate and interfere with the router. Use the exact screws provided.
  • Forgetting to unplug: Working on the saw with it plugged in is a serious hazard. Always unplug first.
  • Cutting the hole too small: If the bit opening is too tight, the router bit will hit the wing. Make the hole slightly larger than the bit’s diameter.
  • Overtightening the plate: Cracking the aluminum wing or stripping threads is easy if you overdo it. Snug is enough.

Tips

  • Use a router bit with a bearing guide for edge work; the bearing follows the wood, not the fence.
  • Always feed the wood against the router bit’s rotation (from right to left when looking at the bit from above).
  • For better dust collection, attach a shop vac hose near the router bit.
  • If your router has a variable speed, run it at a lower speed for large bits.
  • Keep the router’s power cord out of the way; use a cord holder or tape it to the saw’s leg.
  • Apply a thin coat of paste wax to the wing and plate to reduce friction.

Troubleshooting

  • The router bit won’t go through the hole: The opening is too small. Remove the wing, enlarge the hole with a file or router, and reattach.
  • The wing is not level: Loosen the bolts, place thin washers or shims under the low side, and retighten. Check with a straightedge.
  • The router vibrates excessively: Tighten the mounting screws, check that the router’s base is seated flat, and ensure the bit is fully inserted and tightened.
  • The wood burns or cuts rough: The bit is dull, the speed is too high, or the feed rate is too slow. Change the bit, lower the speed, or push the wood faster.
  • The plate moves during use: The screws are loose. Remove the wing and retighten from underneath, or add thread-locking adhesive.
  • The router won’t fit the plate: Your router’s base hole pattern is different. You may need a different plate or an adapter ring. Measure the hole spacing and compare to the plate’s specs.

Frequently Asked Questions

Can I attach any router to my Ryobi table saw?

Most fixed-base and plunge routers with a flat base can be mounted, but you need a universal plate that matches your router’s screw pattern. Check the plate’s compatibility list or measure the distance between your router’s mounting holes.

Do I need to remove the saw blade guard?

No. The router is mounted on the extension wing, away from the blade. Keep the blade guard in place for normal sawing operations.

Can I use the saw’s fence with the router?

Yes, that’s the main advantage. The fence acts as a guide for the router, giving you accurate, straight cuts. Just ensure the fence is parallel to the router bit.

Will this void my warranty?

Modifying the saw’s extension wing may void the warranty on that part, but it generally doesn’t affect the saw’s motor or other components. Check your warranty terms.

Can I mount the router on the left side?

Yes, if your saw has a left extension wing. The process is the same, but you’ll need to ensure the router bit is positioned correctly relative to the fence.

What size router bit can I use?

Use bits that fit through the hole in the plate. Typically, bits up to 1/2″ shank are fine. Larger bits may require a bigger opening.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →