This guide shows you how to verify the actual usable capacity of an SSD in Windows, macOS, and Linux. You’ll learn to see the true formatted capacity (which differs from the advertised size due to binary vs. decimal units and reserved space) and how to spot fake or mislabeled drives. No special tools are required—just the operating system’s built-in utilities.
What You’ll Need
- An SSD connected to your computer (internal or external via USB/SATA/NVMe).
- Administrator or sudo access to run some commands (especially on Linux).
- For external drives: a working cable and port.
Step-by-Step
Windows
- Open Disk Management: Press Win + X and select Disk Management. Alternatively, search for “Create and format hard disk partitions” in the Start menu.
- Locate your SSD: In the lower half of the window, find your drive (e.g., Disk 0, Disk 1). It will show the total size in GB (e.g., 465.76 GB for a 500 GB drive). This is the real usable capacity after formatting and overhead.
- Check the partitions: Each partition shows its size. The sum of all partitions on the disk equals the usable capacity (minus any hidden system partitions).
- For a more detailed view: Open Command Prompt as administrator and run
diskpart, thenlist disk. The sizes shown are in GB and are the raw capacity as the OS sees it.
macOS
- Open Disk Utility: Go to Applications > Utilities > Disk Utility.
- Select the physical drive: In the sidebar, click Show All Devices (View menu) and select the actual disk (e.g., APPLE SSD AP0512M), not the volume underneath it.
- Read the capacity: The top of the window shows the total capacity in GB (e.g., 500.28 GB). This is the real size after the controller’s reserved space (over-provisioning) is subtracted.
- Check the volume: Click the volume (e.g., Macintosh HD) to see its formatted capacity, which is slightly less due to the file system.
- Terminal alternative: Open Terminal and run
diskutil listto see the disk size in bytes (e.g., 500277790720 bytes). Divide by 1,000,000,000 to get GB.
Linux
- Use lsblk: Open a terminal and run
lsblk -o NAME,SIZE,MODEL. This lists all block devices with their sizes. Find your SSD (e.g., sda, nvme0n1). The size shown is the raw capacity (e.g., 465.8G). - Use fdisk: Run
sudo fdisk -l /dev/sda(replace sda with your drive). The output shows disk size in bytes and sectors. - Use smartctl (if installed): Run
sudo smartctl -i /dev/sdato see the drive’s reported capacity in the IDENTIFY data. This is the manufacturer’s raw capacity before formatting. - Check partitions: Use
lsblkagain to see partition sizes. The sum of partitions should equal the disk size minus any unallocated space.
Common Mistakes
- Confusing GB and GiB: Manufacturers advertise using decimal (1 GB = 1,000,000,000 bytes), while operating systems often display in binary (1 GiB = 1,073,741,824 bytes). A 500 GB drive shows as ~465.76 GiB in Windows. This is normal, not a defect.
- Looking at the volume instead of the disk: On macOS, the volume’s capacity is smaller than the disk’s capacity because the volume is a partition on the disk. Always check the physical disk.
- Ignoring hidden partitions: Windows creates a 100 MB system partition and a recovery partition. These take up space, so the sum of visible partitions may be less than the disk’s total capacity.
- Using third-party tools that report raw bytes: Some tools report the exact byte count, which can be confusing. Always convert to GB or GiB for a human-readable number.
Tips
- Use the OS’s built-in tools first: They are reliable and require no installation.
- Check the drive’s label and model number: Search the model online to see its official capacity. A 1 TB drive showing 500 GB is a red flag.
- For external drives: If the drive is USB, make sure it’s connected directly (not through a hub) to avoid detection issues.
- On Linux, use
lsblk -bto see sizes in bytes: This gives the exact raw capacity, which you can compare to the manufacturer’s spec. - If you suspect a fake drive: Run a full write/read test using
f3(Fight Flash Fraud) on Linux orH2testwon Windows. These tools write data to the entire drive and verify it, exposing drives that falsely report capacity.
Troubleshooting
- Drive not showing up: If the SSD doesn’t appear in Disk Management, Disk Utility, or
lsblk, check the physical connection (SATA cable, power, M.2 seating). Try a different port or cable. - Capacity shows as 0 or extremely small: This often indicates a driver issue or a failing drive. Try updating the storage controller driver (Windows) or checking
dmesgon Linux for errors. - Capacity shows as unallocated space: If the drive is new, it may need to be initialized and partitioned. In Windows, right-click the disk and select “Initialize Disk”. On macOS, use Disk Utility to erase it. On Linux, use
fdiskorparted. - macOS shows a different size than Windows: This is due to different rounding. macOS uses decimal (1 GB = 1,000,000,000 bytes) for display, while Windows uses binary (1 GB = 1,073,741,824 bytes). The actual byte count is the same.
- Linux shows the drive but no partitions: This is normal for a blank drive. You need to create a partition table and partitions before use.
Frequently Asked Questions
Why does my 1 TB SSD show only 931 GB?
Because 1 TB is 1,000,000,000,000 bytes, but the operating system reports in GiB (1 GiB = 1,073,741,824 bytes). 1,000,000,000,000 / 1,073,741,824 ≈ 931.32 GiB. This is normal.
Is the capacity shown in Disk Management the real usable space?
Yes, it’s the raw capacity as seen by the OS after the drive’s controller reserves some space for over-provisioning and bad block management. It’s the maximum you can use for partitions.
Can I recover the hidden reserved space on my SSD?
No. The reserved space (over-provisioning) is managed by the SSD’s firmware and is not accessible. It’s essential for performance and longevity.
How do I check if my SSD is fake or has less capacity than advertised?
Use a tool like f3 (Linux) or H2testw (Windows) to write and read back data across the entire drive. If the drive fails verification, it’s likely fake.
Why does my external SSD show a different capacity on different computers?
This is usually due to different operating systems using different units (decimal vs. binary) or file system overhead. The raw capacity is the same.
Do I need to format my new SSD before checking capacity?
No, you can check the raw capacity without formatting. However, if the drive is uninitialized, you may need to initialize it first to see partitions.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Fix Text Cursor Turning White in Windows 11
- Force Quit Non-Responding Apps on Mac: 6 Ways
- Chromebook Not Charging? Fix It Fast
- iPhone Won’t Make Calls but Texts Work? Fixes
- Android to iPhone Hotspot: Connect & Fix Issues
- Fix Bluetooth Not Working on Discord Mobile