sodcalculator

10 Tech How-To

Boot from Intel Optane SSD: BIOS & Linux Setup

Guide 10-51585 · Updated · Step by step

This guide walks you through configuring your BIOS and Linux installation to boot from a standalone Intel Optane SSD. It covers enabling the necessary NVMe and VMD settings, preparing the drive, and installing or migrating your OS. You’ll need a working Linux system (or a live USB) and access to your motherboard’s UEFI/BIOS setup.

What You’ll Need

  • An Intel Optane SSD (M.2 or U.2 form factor) installed in your system.
  • A motherboard with an M.2 slot that supports NVMe (or a U.2 port).
  • A Linux installation USB or an existing Linux system for migration.
  • Access to your BIOS/UEFI setup (usually by pressing Del, F2, or F12 during boot).

Step-by-Step

  1. Back up any existing data on the Optane SSD. If the drive is new, skip this. If it contains data, back it up to another storage device.
  2. Enter your BIOS/UEFI setup. Restart your computer and press the key indicated on the splash screen (often Del, F2, or F12).
  3. Enable Intel VMD (Volume Management Device) if your motherboard supports it. This is usually found under Advanced > VMD setup or Intel Rapid Storage Technology. Set VMD mode to “Enabled” and enable VMD for the PCIe slot where your Optane SSD is connected. Note: Some motherboards require VMD to be enabled for the Optane drive to be recognized as a boot device. If your motherboard does not have VMD, skip this step.
  4. Ensure the SATA/NVMe mode is set to AHCI/NVMe. In the SATA configuration section, set SATA mode to AHCI (not RAID) unless you are using VMD with RAID. For NVMe drives, the mode is usually automatic, but verify that the PCIe link speed is set to Gen3 or higher if supported.
  5. Disable CSM (Compatibility Support Module) and enable UEFI boot. In the Boot section, set Boot Mode to UEFI (not Legacy). Disable CSM if present. This ensures the system boots via UEFI, which is required for NVMe drives in most cases.
  6. Set the boot order. In the Boot Priority or Boot Order menu, ensure that the entry for your Optane SSD (often listed as “Windows Boot Manager” if it has an OS, or “UEFI: [Optane SSD model]”) is first. If the drive is not listed, re-check the VMD and NVMe settings.
  7. Save and exit BIOS. Press F10 (or the save-and-exit key) and confirm. Your system will reboot.
  8. Install Linux on the Optane SSD. Boot from your Linux installation USB. During installation, when you reach the disk partitioning step, select the Optane SSD as the target. If you are migrating, you can clone your existing system to the Optane SSD using tools like dd or rsync.
  9. After installation, ensure the bootloader is installed on the Optane SSD. Most Linux installers (Ubuntu, Fedora, etc.) will automatically install GRUB to the first disk. Verify that the bootloader is installed to the EFI System Partition (ESP) on the Optane SSD, not on another drive.
  10. Reboot and test. After installation, remove the USB and reboot. Your system should boot from the Optane SSD. If it doesn’t, re-enter BIOS and manually select the boot device.

Common Mistakes

  • Forgetting to enable VMD: On many Intel platforms, the Optane SSD will not appear as a boot device unless VMD is enabled. Check your motherboard manual for the correct VMD settings.
  • Leaving CSM enabled: CSM can interfere with NVMe boot. Disable it and use UEFI mode.
  • Installing GRUB to the wrong disk: If you have multiple drives, the installer might place the bootloader on another disk. Manually select the Optane SSD as the target for the bootloader.
  • Using an MBR partition table: UEFI boot requires a GPT partition table. If your drive is MBR, convert it to GPT during installation or use gdisk to convert it.

Tips

  • Update your BIOS: Ensure you have the latest BIOS from your motherboard manufacturer, as Optane support and VMD stability improve with updates.
  • Use a recent Linux kernel: Kernels 5.0 and later have good NVMe and VMD support. Use a current distribution like Ubuntu 22.04+, Fedora 36+, or Arch Linux.
  • Check the NVMe driver: After boot, run lsblk to confirm the drive is recognized. Use nvme list to see detailed NVMe information.
  • Consider using a dedicated EFI partition: If you have multiple OSes, create a separate EFI System Partition on the Optane SSD to avoid conflicts.

Troubleshooting

  • The Optane SSD is not detected in BIOS: Re-seat the drive, try a different M.2 slot (some slots share bandwidth with SATA ports), and verify that the slot is configured for PCIe/NVMe mode in BIOS.
  • The system boots to a black screen after installation: This often indicates a bootloader issue. Boot from a live USB, chroot into your installed system, and reinstall GRUB with grub-install /dev/nvme0n1 and update-grub.
  • Linux does not see the drive after boot: Check if VMD is enabled. If yes, you may need to load the vfio-pci or nvme driver. In some cases, you need to add pci=realloc to the kernel command line.
  • Boot is slow or hangs: Ensure that the drive is set as the first boot device and that no other drives are interfering. Also check that the UEFI boot order is correct.
  • Windows was previously on the drive: If you are replacing Windows with Linux, make sure to delete all partitions on the Optane SSD during installation to avoid leftover boot entries.

Frequently Asked Questions

Do I need Intel VMD enabled to boot from an Optane SSD?

Not always, but on many modern Intel platforms, VMD is required for the drive to be recognized as a boot device. If your motherboard has VMD, enable it; if not, the standard NVMe mode should work.

Can I use an Optane SSD as a regular NVMe drive?

Yes, an Optane SSD is a standard NVMe drive. You can use it for storage or as a boot drive without any special Intel software, as long as your BIOS supports NVMe boot.

Will Linux support Intel Optane memory acceleration (RST) on a second drive?

Linux does not support Intel Rapid Storage Technology (RST) for Optane memory acceleration. However, you can use the Optane drive as a standalone NVMe SSD, which is what this guide covers.

Can I clone my existing Linux installation to the Optane SSD?

Yes, you can clone using tools like dd or rsync. Ensure the target partition sizes are correct and that the bootloader is reinstalled properly.

Why is my Optane SSD not showing up in the boot menu?

This is usually due to VMD being disabled, CSM enabled, or the drive not being formatted with GPT. Check your BIOS settings and re-format the drive with GPT if needed.

Do I need to install any special drivers in Linux?

No, the standard NVMe driver in the Linux kernel supports Optane SSDs. Just ensure your kernel is recent enough (5.0 or later).

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →