sodcalculator

10 Tech How-To

3D Print PC Accessories That Fit Your Case

Guide 10-44644 · Updated · Step by step

This guide walks you through designing and 3D printing custom PC accessories—cable clips, fan shrouds, GPU supports, drive brackets, and more—that fit your specific case perfectly. You’ll learn how to measure accurately, model in free software, and print parts that mount securely without guesswork. No prior CAD experience is needed, just a printer and a caliper.

What You’ll Need

  • A 3D printer (FDM recommended) with basic slicing software (Cura, PrusaSlicer, etc.)
  • Digital caliper (essential for accurate measurements)
  • Free CAD software: Tinkercad (beginner) or Fusion 360 (free personal license)
  • Screwdriver set (to check screw sizes and clearances)
  • Access to your PC case (open side panels)
  • Optional: M3/M4 screws, zip ties, or heat-set inserts

Step-by-Step

  1. Identify the accessory you need. Common useful items: cable management clips, fan spacers, GPU anti-sag brackets, PSU cable combs, or a custom front-panel cover. Choose one that solves a real problem—don’t print for the sake of printing.
  2. Take precise measurements with the caliper. For a clip that mounts to a case hole, measure the hole diameter, the material thickness around it, and the cable bundle width. For a bracket, measure the distance between mounting points (e.g., fan screw holes are usually 105mm apart for 120mm fans). Write every number down—do not rely on memory.
  3. Measure the clearance space. Check how much room exists between the component and the side panel, GPU, or drive cage. Use a ruler or caliper to get the maximum depth and width your part can occupy. This prevents printing something that won’t physically fit.
  4. Check screw sizes and thread types. Most PC cases use #6-32 or M3 screws for drives and fans. Measure the screw diameter and pitch with the caliper, or test-fit a known screw. Design your holes slightly larger (0.3–0.5mm) for clearance, or model them for press-fit inserts.
  5. Start modeling in Tinkercad or Fusion 360. Begin with basic shapes: a cylinder for a cable clip, a box for a bracket. Use the “ruler” tool to set exact dimensions from your measurements. For holes, use the “hole” feature—don’t just make a circle on top of a box; ensure it’s a true hole that cuts through.
  6. Add tolerances. For a clip that snaps over a tab, add 0.2–0.3mm clearance on each side. For a press-fit insert, design the hole 0.1mm smaller than the insert’s outer diameter. For screw holes, add 0.4mm clearance for easy threading.
  7. Design for print orientation. Avoid overhangs greater than 45 degrees. If you’re printing a fan shroud, orient it so the flat face is on the build plate. For a clip, print it on its side so the clip’s opening faces upward—this avoids supports inside the clip.
  8. Export as STL and slice. Import the STL into your slicer. Use 3–4 perimeters and 20–30% infill for structural parts. For clips that flex, use 2 perimeters and 15% infill to keep them flexible. Set layer height to 0.2mm for a good balance of speed and quality.
  9. Print a test piece first. Print a small section of the part (e.g., just the clip’s opening) to check fit before committing to the full print. This saves time and filament.
  10. Test-fit and adjust. After printing, try mounting the part. If it’s too tight, sand the contact areas or reprint with 0.1mm more clearance. If it’s too loose, reprint with 0.1mm less. Iterate until it fits snugly.
  11. Finalize with finishing touches. If the part will be visible, consider printing in a color that matches your build. Use a small file to remove stringing or rough edges. For parts that hold cables, add a zip tie slot if needed.

Common Mistakes

  • Measuring only once. Always measure twice—especially hole spacing. A 1mm error can make a part useless.
  • Forgetting about the side panel. A fan shroud that’s 5mm too deep will hit the glass. Always check clearance in all three axes.
  • Using the wrong tolerance. Too tight and the part won’t fit; too loose and it rattles. Start with 0.2mm clearance and adjust from there.
  • Printing with too much infill. For clips and brackets, 100% infill is overkill and makes them brittle. Use 20–30% for strength and flexibility.
  • Ignoring print orientation. Printing a clip vertically can cause layer lines to separate when flexed. Print it horizontally for strength.

Tips

  • Use PETG or ABS for parts near heat sources (e.g., GPU backplates). PLA can soften above 60°C.
  • Design with “living hinges” for cable clips—make the clip’s arm thin (1–2mm) so it bends without breaking.
  • Add a small chamfer or fillet to the edges of holes to make insertion easier.
  • If you’re unsure about a dimension, print a calibration cube with a hole of the same size to test your printer’s accuracy.
  • Use a digital caliper’s “zero” function to measure relative distances, like the gap between two screw holes.
  • Save your CAD files with version numbers so you can revert if a change makes things worse.

Troubleshooting

  • The part is too tight. Sand the contact areas with 100-grit sandpaper, or reprint with 0.1mm more clearance. If it’s a screw hole, run a tap through it.
  • The part is too loose. Add a thin layer of tape to the mounting point, or reprint with 0.1mm less clearance. For clips, you can also add a small dab of hot glue.
  • The part warps during printing. Use a heated bed (60°C for PLA, 100°C for ABS) and an enclosure for ABS. Add a brim to increase adhesion.
  • The part snaps when flexing. Reduce infill to 15–20%, increase wall count to 3, or print with a more flexible filament like TPU for clips.
  • The screw holes don’t align. Re-measure the hole spacing with the caliper—it’s likely off by 0.5mm. Also check that the part isn’t warped; print a flat test piece.
  • The part melts near the GPU. Switch to PETG or ABS, which have higher glass transition temperatures. Also ensure the part isn’t blocking airflow.

Frequently Asked Questions

Do I need a caliper to measure my case?

Yes, a digital caliper is essential. A ruler won’t give you the precision needed for holes and tolerances. You can get a basic one for under $15.

Can I use PLA for PC accessories?

Yes, for most non-heat areas like cable clips and brackets. Avoid PLA near GPUs or radiators where temps can exceed 60°C. PETG is a safer all-around choice.

What’s the best layer height for these parts?

0.2mm is a good balance. For small text or fine details, use 0.12mm. For functional parts, 0.2mm is fine.

How do I make a clip that snaps over a case tab?

Measure the tab’s thickness and width. Design the clip’s opening 0.2–0.3mm smaller than the tab, and make the clip’s arms thin (1.5mm) so they flex. Print the clip horizontally so the arms are strong.

Do I need supports for these designs?

Mostly no, if you design with print orientation in mind. Avoid overhangs over 45 degrees. For internal holes, they print fine without supports if they’re not too deep.

Can I sell the accessories I design?

Yes, if you designed them from scratch. If you used a template or someone else’s model, check the license. Many Thingiverse designs are for personal use only.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →