sodcalculator

10 Tech How-To

How to Measure Windows for Square Feet

Guide 10-51245 · Updated · Step by step

This guide shows you how to measure any window to find its area in square feet. You’ll take two simple measurements (width and height), multiply them, and get the total square footage. This is useful for ordering curtains, blinds, glass replacement, or estimating paint or film coverage.

What You’ll Need

  • Tape measure (metal or cloth, at least 6 feet long)
  • Notebook and pen (or a phone notes app)
  • Step stool or ladder if the window is high
  • Calculator (optional, but handy)

Step-by-Step

  1. Decide what you’re measuring. For most purposes (glass replacement, window film, or rough area), measure the glass or the inside of the frame. For curtains or blinds, you’ll need the outside of the frame or the window opening. Write down which you’re measuring so you don’t mix them up.
  2. Measure the width. Place the tape measure at the left edge of the window (inside edge of the frame, or glass edge) and extend it to the right edge. Keep the tape straight and level. Record this number in inches to the nearest 1/8 or 1/16 inch.
  3. Measure the height. Place the tape at the top edge and measure down to the bottom edge, keeping the tape vertical. Record this in inches.
  4. Measure twice. Repeat both measurements to confirm accuracy, especially if the window is old or not perfectly square. If you get different numbers, use the larger one (for coverage) or the smaller one (for fitting a pane).
  5. Convert to square feet. Multiply the width (in inches) by the height (in inches) to get the area in square inches. Then divide that number by 144 (since 1 square foot = 144 square inches). The result is the area in square feet.
  6. Round appropriately. For most purposes, round to the nearest 0.1 or 0.5 square foot. For ordering materials, round up to the next whole number to have a little extra.

Common Mistakes

  • Mixing units: Measuring width in inches and height in feet, then multiplying directly. Always use the same unit for both.
  • Forgetting to divide by 144: Multiplying width × height gives square inches, not square feet. The division is essential.
  • Measuring the wrong part: Using the outside frame for glass, or vice versa. Be consistent with what you’re ordering.
  • Not accounting for trim: For curtains, you might want the width of the window plus trim, not just the glass. Decide before measuring.
  • Ignoring non-rectangular windows: If your window is arched or triangular, a simple width × height won’t work. You’ll need a different formula (see FAQ).

Tips

  • Measure to the nearest 1/8 inch for accuracy, but don’t stress over 1/16 inch differences.
  • If the window has a grid or mullions, measure the entire opening, not each pane, unless you’re replacing individual glass panes.
  • For a rough estimate, you can round to the nearest inch, but for ordering custom items, use exact measurements.
  • Write down the measurements immediately—don’t rely on memory.
  • If you’re measuring multiple windows, label each set (e.g., “living room north window”) to avoid confusion.

Troubleshooting

  • Window is not perfectly rectangular: Measure at three points (top, middle, bottom for width; left, middle, right for height) and use the average or the largest, depending on your need. For a tight fit, use the smallest.
  • You get a different number each time: The tape may be slipping or you may be reading it at an angle. Have someone hold the tape, and read it straight on. If the window is truly irregular, measure at multiple points and note the range.
  • You need square footage for multiple windows: Sum the individual square footages. Don’t add the widths and heights together first—that would be wrong.
  • The window is too high to reach: Use a ladder safely, or use a laser distance measurer. If you must estimate, be aware it will be less accurate.
  • You measured in feet and inches (e.g., 3 ft 5 in): Convert the inches to a decimal of a foot (5 in ÷ 12 = 0.4167 ft), then multiply. Or convert everything to inches first.

Frequently Asked Questions

How do I measure a circular or arched window?

For a circle, measure the diameter (width across the center), divide by 2 to get the radius, then use the formula πr² (3.14 × radius × radius) to get square inches, then divide by 144. For an arch, treat it as a rectangle plus half a circle, and calculate each part separately.

Should I measure the glass or the frame?

It depends on what you’re buying. For glass replacement, measure the glass itself. For blinds or curtains, measure the inside of the frame (for inside-mount) or the outside of the frame (for outside-mount). For window film, measure the glass.

What if my window has a grid (mullions)?

For the whole window’s square footage, measure the entire opening, including the grid. For individual panes, measure each pane separately. If you’re ordering film, you might need to cut around the grid, so measure the full glass area.

How accurate do my measurements need to be?

For most purposes, within 1/4 inch is fine. For custom glass or tight-fitting blinds, aim for 1/8 inch. For just estimating square footage, rounding to the nearest inch is usually adequate.

Can I measure in feet directly instead of inches?

Yes, but be careful. Measure width and height both in feet (using decimals, e.g., 3.5 ft), then multiply to get square feet directly. This avoids the 144 division, but many people find inches easier to read on a tape measure.

Why do I need to divide by 144?

Because there are 12 inches in a foot, so a square foot is 12 × 12 = 144 square inches. When you multiply width (in inches) by height (in inches), you get square inches. Dividing by 144 converts that to square feet.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →