This guide walks you through pairing Shokz OpenRun bone-conduction headphones with an iPhone or Android phone. You’ll learn the exact button presses for both initial pairing and reconnecting to a previously paired device, plus how to fix common connection issues.
What You’ll Need
- Your Shokz OpenRun headphones (charged)
- An iPhone (iOS 13 or later) or Android phone (Android 8.0 or later)
- The Bluetooth settings menu on your phone
Step-by-Step
Prepare the Headphones
- Charge the headphones. If the battery is completely drained, plug them into a USB charger for at least 10 minutes before attempting to pair. A low battery can prevent the pairing mode from activating.
- Locate the power button. On the OpenRun, the power button is on the right ear piece, near the bottom. It’s the larger of the two buttons on that side.
Enter Pairing Mode
- Turn the headphones off. If the LED light (next to the power button) is solid red or blue, hold the power button for about 3 seconds until the LED flashes red and you hear a power-off tone.
- Press and hold the power button for 5 seconds. Keep holding it. You will see the LED flash red and blue alternately. You’ll also hear a voice prompt saying “pairing.” This indicates the headphones are now discoverable.
- Release the button once you see the alternating red/blue flashes. The headphones will stay in pairing mode for about 2 minutes.
Pair with Your Phone
- Open your phone’s Bluetooth settings.
- iPhone: Go to Settings > Bluetooth. Make sure Bluetooth is toggled on.
- Android: Go to Settings > Connected devices (or Bluetooth on older versions). Make sure Bluetooth is on.
- Wait for the headphones to appear. Look for a device named OpenRun by Shokz (or sometimes just OpenRun) in the list of available devices. It may take a few seconds to show up.
- Tap the device name. Your phone will connect. You’ll hear a voice prompt saying “connected” and the LED light will turn solid blue (or stop flashing). The headphones will also appear under “My Devices” or “Paired devices” on your phone.
Reconnecting Later
- Simply turn the headphones on. With Bluetooth enabled on your phone and the headphones within range (about 30 feet), press and hold the power button for about 3 seconds until the LED flashes blue. They should automatically reconnect to the last paired phone.
Common Mistakes
- Holding the power button too long. If you hold it for more than 6-7 seconds, the headphones may enter a forced power-off or reset mode instead of pairing mode. The sweet spot is about 5 seconds.
- Not waiting for the alternating LED. Releasing the button as soon as the LED turns on (solid blue) just powers the device on normally. You must wait for the red/blue flashing sequence.
- Pairing while the headphones are connected to another device. If your OpenRun is already connected to a laptop or another phone, it won’t be discoverable. Disconnect them from that device first (turn off its Bluetooth or put the headphones in pairing mode again).
- Ignoring the old pairing list. If you’ve previously paired the headphones to your phone, but they won’t connect, go to your phone’s Bluetooth settings, find the OpenRun entry, tap the “i” icon (iPhone) or gear icon (Android), and select “Forget This Device.” Then start the pairing process from scratch.
Tips
- Use the Shokz app (optional). The Shokz app (available on iOS and Android) can help manage connections, update firmware, and adjust EQ settings. It’s not required for basic pairing, but it can make reconnecting to multiple devices easier.
- Multipoint connection. The OpenRun can remember two paired devices at once. To connect to a second phone, put the headphones in pairing mode (steps 3-5) and pair it. The headphones will switch between the two most recently used devices.
- Keep the headphones charged. If the battery is very low, the headphones may not enter pairing mode reliably. A quick 10-minute charge usually solves this.
- Check for interference. If you’re in an area with many Bluetooth devices, pairing can be flaky. Move away from other electronics and try again.
Troubleshooting
The headphones don’t appear in the Bluetooth list.
- Make sure the headphones are in pairing mode (LED flashing red/blue). If not, repeat steps 3-5.
- Turn your phone’s Bluetooth off and on again.
- Restart your phone. This clears the Bluetooth cache and often resolves discovery issues.
- If you’ve paired before, forget the device on your phone and try again.
Pairing fails or the connection drops immediately.
- Ensure the headphones are charged (at least 20%).
- Move closer to your phone (within 3 feet) during pairing.
- Check for other Bluetooth devices that might be interfering.
- Try a factory reset: hold the power button and the volume up button together for about 5 seconds until the LED flashes red twice. Then re-pair.
The headphones connect but there’s no sound.
- Check the volume on both the headphones (use the volume rocker on the left ear piece) and your phone.
- Make sure the audio is playing through the OpenRun. On your phone, check the audio output device (often in the music app or the control center/quick settings).
- If you’re on a call, ensure the call audio is routed to the headphones (check the in-call audio options).
The headphones connect to my phone but not to my laptop.
- The OpenRun can only be actively connected to one device at a time for audio. If they’re connected to your phone, disconnect them (turn off Bluetooth on the phone) before trying to connect to the laptop.
- On the laptop, remove the OpenRun from the Bluetooth device list and re-pair from scratch.
Frequently Asked Questions
How do I reset my Shokz OpenRun?
To factory reset, hold the power button and the volume up (+) button simultaneously for about 5 seconds until the LED flashes red twice. This clears all paired devices and restores default settings.
Can I connect the OpenRun to two phones at once?
Yes, the OpenRun supports multipoint connection. You can pair it with two devices (e.g., a phone and a laptop) and it will switch between them. To add a second device, put the headphones in pairing mode and pair it like normal.
Why does my OpenRun keep disconnecting?
This is usually caused by low battery, being out of range (over 30 feet), or interference from other Bluetooth devices. Try charging, moving closer, and re-pairing after forgetting the device on your phone.
How do I know if my OpenRun is charging?
When you plug in the magnetic charging cable, the LED light will turn solid red. When fully charged, it turns solid blue. A full charge takes about 2 hours.
Do I need the Shokz app to pair?
No, the app is optional. The standard Bluetooth pairing process works fine without it. The app adds features like EQ adjustment and firmware updates.
What do I do if the voice prompts are in a language I don’t understand?
You can change the voice prompt language through the Shokz app. Connect the headphones to the app, go to settings, and select your preferred language.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Show User Library in macOS High Sierra & Sierra
- Device Manager Shortcut: Windows 10 Desktop
- How to Remove Forgotten Passcode from iPhone
- Fix Slow Wi-Fi Problem iPhone X: 9 Steps
- How to Check if a Candidate Accepts Crypto Donations
- How to Listen to Deleted Voicemails on iPhone