sodcalculator

10 Tech How-To

Restore Apple Watch Without iPhone: Full Guide

Guide 10-51411 · Updated · Step by step

If your iPhone is lost, broken, or simply not available, you can still restore your Apple Watch to factory settings directly from the watch itself. This is useful before selling the watch, troubleshooting a serious software problem, or when you need to pair it with a new phone later. The process is built into watchOS and requires no computer or phone, though you will need to keep the watch on its charger for the entire procedure.

What You’ll Need

  • Your Apple Watch
  • The Apple Watch magnetic charging cable and power adapter
  • The passcode for the watch (if one is set)
  • Your Apple ID password (only if Activation Lock is enabled, which it is by default)

Step-by-Step

  1. Place the watch on its charger. Connect the magnetic charging cable to the back of the watch and plug it into a power source. The watch must stay on the charger for the entire restore process; if it runs out of battery mid-restore, it can become stuck.
  2. Press and hold the side button. This is the flat, rectangular button below the Digital Crown. Keep holding it until you see the Power Off slider appear on the screen.
  3. Press and hold the Digital Crown. While the Power Off slider is visible, press and hold the Digital Crown firmly. Do not release either button. After a few seconds, the watch will begin resetting and the Apple logo will appear.
  4. Keep holding until the reset completes. Continue holding the side button and Digital Crown until the watch finishes erasing and restarts. This can take several minutes. You will know it is done when you see the “Hello” screen or the pairing screen with a language selection.
  5. Set up the watch again (optional). If you are keeping the watch, you can now pair it with an iPhone as you would a new device. If you are selling it, leave it on the “Hello” screen; the new owner will pair it with their own iPhone.

Common Mistakes

  • Letting the battery die. A restore that is interrupted by a dead battery can leave the watch in an unusable state. Always start with a charge above 50% and keep it plugged in.
  • Releasing the buttons too early. Many users let go as soon as the Apple logo appears, but the watch is still erasing. Keep holding both buttons until the watch restarts and shows the setup screen.
  • Confusing the side button with the Digital Crown. The side button is below the crown. The reset requires both, so mixing them up will not start the process.
  • Forgetting Activation Lock. After the restore, the watch will ask for the Apple ID password of the account it was previously linked to. If you cannot provide it, the watch is unusable. This is a security feature, not a bug.

Tips

  • Back up first if possible. If you still have access to your iPhone, open the Watch app and let it back up before you wipe the watch. Most watch data syncs from the phone, so a backup makes restoring easier later.
  • Use a stable power source. Plug the charger into a wall outlet rather than a laptop USB port, which may provide inconsistent power.
  • Be patient. The erase can take 5–10 minutes on older models. If the screen stays black for a while, do not assume it is frozen; give it time.
  • Check for a pending update. If the watch was mid-update when it failed, the restore may take longer as it clears partial software.

Troubleshooting

The watch does not show the Power Off slider. Make sure you are pressing the side button, not the crown, and hold it for at least 3 seconds. If nothing appears, the watch may be completely drained; charge it for 15 minutes and try again.

The watch restarts but still shows your old watch face or data. The restore did not complete. Repeat the process, but this time hold both buttons for at least 10 seconds after the Apple logo appears. Do not release until you see the language selection screen.

The watch asks for an Apple ID password you do not know. This is Activation Lock. You must enter the Apple ID and password that were originally used on the watch. If you cannot, contact Apple Support with proof of purchase. There is no workaround.

The watch is stuck on the Apple logo for over 30 minutes. Force a restart by holding both buttons for 20 seconds until the screen goes black, then release and press the side button to turn it on. If it still hangs, try the restore again from step 1.

The watch shows an exclamation point or a red triangle. This indicates the watch entered recovery mode. It may be recoverable by repeating the reset process, but if it persists, the watch likely needs service.

Frequently Asked Questions

Will this erase all my data? Yes, a restore wipes the watch completely, returning it to factory settings. Any data that was only on the watch (like some workout history) will be lost unless it synced to iCloud.

Can I pair the watch with a new iPhone after this? Yes, after the restore the watch appears as a new device. Open the Watch app on your new iPhone and follow the pairing prompts.

Do I need to remove the watch from my Apple ID first? Ideally yes, but if you cannot access your iPhone, the restore itself will trigger Activation Lock. You will still need your Apple ID password to finish setup later.

Will this fix a frozen or unresponsive watch? Often yes. A restore clears the software and can resolve many glitches. However, if the issue is hardware-related, the restore will not help.

How long does the restore take? Typically 5 to 10 minutes, but it can take longer if the watch has a low charge or older hardware.

Does this work on all Apple Watch models? Yes, the button combination works on all models from the original Apple Watch through the current Series and Ultra models, as long as they run watchOS 4 or later.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →