sodcalculator

10 Tech How-To

Sector by Sector SSD Clone: Full Guide

Guide 10-44568 · Updated · Step by step

This guide walks you through cloning an SSD sector by sector, which copies every single block from the source drive to the target, including the partition table, unallocated space, and deleted files. This is essential when you want an exact duplicate for forensic work, data recovery, or moving a system with hidden recovery partitions. You’ll need a second SSD with at least the same capacity as the source, a USB-to-SATA adapter or an available internal bay, and cloning software that supports raw sector cloning.

What You’ll Need

  • Source SSD (the one being cloned)
  • Target SSD (the destination; must be equal or larger in capacity)
  • A way to connect both drives to the same computer (internal SATA ports, USB adapters, or a docking station)
  • Cloning software that supports sector-by-sector mode (e.g., Clonezilla, dd on Linux, Macrium Reflect, or a similar tool)
  • If using a laptop, a USB-to-SATA adapter for the target drive
  • Patience – sector cloning can take several hours depending on drive size

Step-by-Step

  1. Back up any important data on the target drive. Sector cloning will overwrite the entire target drive, so move anything you need elsewhere.
  2. Connect both SSDs to your computer. If the target is the same size or larger, you can proceed. For internal drives, power off the PC, connect the target to a free SATA port, then boot up. For external connections, plug in the USB adapter after booting.
  3. Identify the correct drive letters or device identifiers. Open Disk Management (Windows) or use lsblk (Linux) to see which disk is the source and which is the target. Double-check the sizes and model numbers – mixing them up can erase the wrong drive.
  4. Choose your cloning software. For Windows, Macrium Reflect Free or Clonezilla (a bootable Linux tool) both offer sector-by-sector cloning. For Linux, the dd command is a classic option. For macOS, use dd in Terminal or a tool like SuperDuper (though sector cloning is less common there).
  5. Run the cloning software in sector-by-sector mode. In Clonezilla, select Device-device then Expert mode and choose raw copy or sector-by-sector. In Macrium Reflect, when you clone a disk, check the option Copy all sectors (or Forensic copy). If using dd, the command is: sudo dd if=/dev/sdX of=/dev/sdY bs=64K status=progress conv=noerror,sync where sdX is the source and sdY is the target.
  6. Confirm the source and target selections. The software will show a summary. Verify the source is the drive you want to copy and the target is the one you want to overwrite. This is your last chance to abort.
  7. Start the clone and wait. Sector cloning copies every byte, so it will take longer than a standard file-based clone. A 500GB SSD can take 1–3 hours over SATA, longer over USB. Do not interrupt the process.
  8. Verify the clone. After completion, disconnect the target drive and boot from it (if you cloned an OS drive). Check that the partition layout matches the source and that files are accessible. Some software offers a verification option – use it if available.
  9. If the target is larger, expand the last partition afterward. Sector cloning copies the exact size of the source, leaving the extra space unallocated. Use Disk Management or a partition tool to extend the last partition to fill the drive.

Common Mistakes

  • Selecting the wrong source or target drive. This is the most catastrophic error. Always verify by size and model number before starting.
  • Using a target drive smaller than the source. Sector cloning will fail or truncate data. The target must be at least the same size in bytes, not just the same advertised capacity (some drives have slightly different usable sizes).
  • Forgetting to back up the target. If you clone to a drive that has data, that data is gone forever.
  • Interrupting the process. A power loss or unplugging a cable during a sector clone can leave both drives in an inconsistent state.
  • Not accounting for drive letter changes. After cloning, the target may appear as a different drive letter. Boot from it to avoid confusion.

Tips

  • Use a direct SATA connection if possible. USB adapters can be slower and less reliable for long operations.
  • Check the health of the source SSD. If the source has bad sectors, the clone may fail. Run a SMART check first.
  • For Linux dd, use a block size of 64K or 128K for better performance. The status=progress option shows you how far along it is.
  • If cloning a system drive, consider doing it from a bootable environment (like Clonezilla) to avoid file locks and inconsistencies.
  • After cloning, use a tool like sha256sum on a few files to verify integrity if you’re paranoid.

Troubleshooting

  • Clone fails with an I/O error. This often indicates bad sectors on the source. Use dd with conv=noerror,sync to skip bad blocks, but understand that the clone will have gaps. For a more robust approach, use a tool like ddrescue which retries reading bad sectors.
  • Target drive is not recognized after cloning. Check the boot order in BIOS/UEFI. If the target is external, it may not be bootable. Try connecting it internally.
  • The cloned drive is larger but shows the same size as the source. You need to extend the partition. Use Disk Management (right-click the partition, Extend Volume) or a tool like GParted.
  • Clone is extremely slow. This is normal for sector cloning. If it’s stuck at 0% for more than 10 minutes, check the connection and the source drive’s health. Sometimes a dying drive can hang the process.
  • Windows won’t boot from the clone. If the source was a system drive, the clone should be bootable, but you may need to repair the boot loader. Boot from a Windows installation USB and use Startup Repair.

Frequently Asked Questions

What is the difference between sector-by-sector cloning and normal cloning?

Normal cloning copies only used files and folders, skipping empty space and deleted data. Sector-by-sector cloning copies every single block, including empty space and deleted files, creating a bit-for-bit duplicate. This is essential for forensic analysis or when you want to recover deleted data.

Can I clone a larger SSD to a smaller one?

No, sector-by-sector cloning requires the target to be at least the same size in bytes. If the target is smaller, the clone will fail. You can use a file-based clone to a smaller drive if the used data fits, but that’s not sector-by-sector.

How long does a sector-by-sector clone take?

It depends on the drive size and connection speed. A 500GB SSD over SATA can take 1–3 hours. Over USB 2.0, it could take 10+ hours. USB 3.0 is faster but still slower than internal SATA.

Will the target SSD be bootable after cloning?

Yes, if the source was bootable and you clone the entire disk, the target should be bootable. However, you may need to change the boot order in BIOS/UEFI. If the target is an external drive, it may not boot unless your system supports USB booting.

Can I use the cloned drive as a backup?

Yes, a sector-by-sector clone is a perfect backup of the entire drive, but it’s not incremental. Any changes you make after the clone won’t be reflected. For ongoing backups, consider a file-based backup tool.

Is it safe to clone a drive with bad sectors?

It’s risky. The clone may fail or have corrupted data. Use a tool like ddrescue that retries bad sectors. Even then, the cloned drive may have issues. It’s better to replace a failing drive and clone only the readable data.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →