If your iPhone’s touch screen is unresponsive or the side buttons aren’t registering, a normal power-off won’t work. This guide shows you how to force a restart—the only reliable way to turn off and reboot an iPhone when the sensor and touch controls fail. You don’t need any tools, and the process takes about 10 seconds.
What You’ll Need
- Your iPhone (any model)
- Nothing else—the buttons are built in
Step-by-Step
The exact button sequence depends on your iPhone model. Check which one you have first.
For iPhone 8 or later (including SE 2nd/3rd gen, X, 11, 12, 13, 14, 15, 16)
- Press and quickly release the Volume Up button. Don’t hold it—just a quick tap.
- Press and quickly release the Volume Down button. Again, a quick tap.
- Press and hold the Side button (the power button on the right edge). Keep holding it.
- Keep holding the Side button even when the screen goes black. Do not let go when you see the “slide to power off” screen—that won’t help if the touch isn’t working.
- Wait for the Apple logo to appear. This usually takes about 10 seconds of holding. Once you see the logo, release the Side button.
- Let the phone boot up. It will restart normally. If the touch screen was the only issue, it should work again after the reboot.
For iPhone 7 and iPhone 7 Plus
- Press and hold the Side button (right edge) and the Volume Down button (left edge) at the same time.
- Keep holding both even after the screen goes black.
- Release both buttons when the Apple logo appears—usually after 10–15 seconds.
For iPhone 6s and earlier (with a Home button)
- Press and hold the Home button (front, below the screen) and the Side or Top button at the same time.
- Keep holding both until the Apple logo shows up.
- Release both buttons and let the phone restart.
Common Mistakes
- Releasing the Side button too early. If you let go when the screen goes dark, the phone may just turn off the display without rebooting. You must keep holding until the Apple logo appears.
- Holding the volume buttons too long. The first two steps are quick taps, not holds. Holding them can trigger a screenshot or accessibility features and mess up the sequence.
- Using the wrong button combo for your model. The iPhone 7 sequence is different from the iPhone 8 sequence. Mixing them up will do nothing.
- Confusing “slide to power off” with a restart. If the screen shows a slider, you’ve held the button too long without the volume taps. The force restart bypasses that screen entirely.
- Giving up after one attempt. Sometimes the buttons need a firmer press, especially if you have a thick case. Try again with more deliberate presses.
Tips
- Remove your case first. A tight case can make the buttons hard to press or stick. Try the force restart without the case if it fails once.
- Make sure the battery isn’t completely dead. If the phone has been off for hours and won’t respond at all, plug it into a charger for at least 15 minutes before trying the force restart. A completely drained battery won’t show the Apple logo no matter what you press.
- Use a firm, deliberate press. The buttons are mechanical; you need to feel them click. Don’t tap lightly.
- This is not a data erasing step. A force restart is safe and doesn’t delete anything. It’s the same as a normal restart, just triggered by buttons instead of the touch screen.
- If the screen is black but you hear sounds or feel vibrations, the display might be broken rather than the sensor. The force restart still works in that case—you just can’t see the Apple logo. Hold the buttons for a full 20 seconds to be sure.
Troubleshooting
Nothing happens when I press the buttons. First, check that you’re using the correct sequence for your model. Then try pressing the buttons harder. If you have a screen protector or case, remove them. If still nothing, connect the phone to a power source and wait 10 minutes—the battery may be completely drained. Then try again.
The Apple logo appears but then the screen goes black again. This can happen if the battery is very low or the phone is stuck in a boot loop. Leave it plugged into power for 30 minutes, then try the force restart again. If the loop continues, you may need to put the phone into recovery mode and restore it via a computer—that’s a separate process that requires a cable and iTunes/Finder.
The phone restarts but the touch screen still doesn’t work. The force restart fixed the software, but the problem is likely hardware—a cracked digitizer, water damage, or a loose display cable. You’ll need to take it to a repair shop. In the meantime, you can still use the phone with a mouse or keyboard connected via Bluetooth or a Lightning/USB-C adapter.
I can’t tell if the phone is off or just frozen. If the screen is completely black and unresponsive, press and hold the Side button for 30 seconds. If it’s just frozen, this will force a restart. If it’s already off, holding the button will turn it on.
The volume buttons don’t click. If they feel stuck or mushy, there may be debris or damage. Try cleaning around them with a soft, dry toothbrush. If they’re physically broken, you can’t do a force restart—you’ll need to wait for the battery to drain completely, then charge and power on normally.
Frequently Asked Questions
Will a force restart delete my data? No. It’s exactly the same as a normal restart—it just uses buttons instead of the touch screen. All your photos, apps, and settings remain intact.
How is this different from just holding the power button? Holding the power button alone brings up the “slide to power off” screen, which requires touch. The force restart sequence bypasses the touch screen entirely and directly reboots the hardware.
Can I force restart an iPhone with a broken Home button? Yes. On iPhone 8 and later, the Home button isn’t used at all. On older models with a physical Home button, that button must work—if it’s broken, you can’t do a force restart on those models.
How often can I do this? As often as needed. There’s no limit or wear-and-tear concern. The buttons are rated for hundreds of thousands of presses.
My iPhone is stuck on the Apple logo. Will this help? Yes, a force restart is the first step to fix a boot loop. If it doesn’t work after a few tries, you’ll need recovery mode and a computer.
Does this work on iPads too? Yes, the same button sequences work on iPads without a Home button (iPad Pro, iPad Air 4th gen and later). For iPads with a Home button, hold Home + Top button together.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Windows 10 Won’t Boot? Fix It in 30 Minutes
- Ubuntu 26.04 LTS Requirements & Hardware Checks
- How to View Wi-Fi Password on iPhone
- How to Stream on Twitch from PC
- GTM vs Facebook Pixel: What’s the Difference?
- ATK0100 Driver: Do You Need to Install It?