This guide walks you through removing root access from a Samsung Galaxy Grand Neo Plus (GT-I9060I) and restoring it to a fully stock, unrooted state. You’ll need a Windows PC, the original USB cable, and a few free tools. The process wipes your phone, so back up anything you want to keep before starting.
What You’ll Need
- Samsung Galaxy Grand Neo Plus (GT-I9060I) with at least 50% battery
- Windows PC (Windows 7, 8, 10, or 11)
- Original Samsung USB cable
- Odin 3.09 or 3.10.6 (download from a trusted source)
- Stock firmware for your exact model and region (search “GT-I9060I stock firmware” on SamMobile or similar)
- Samsung USB drivers installed on the PC
- Backup of your personal data (contacts, photos, messages)
Step-by-Step
- Back up your data. Unrooting via Odin will erase everything on the phone. Copy photos, videos, and documents to a computer or cloud service. Use Samsung Smart Switch or Google backup for contacts and app data.
- Download and extract the stock firmware. Get the correct firmware for the GT-I9060I. It will be a ZIP file. Extract it to a folder on your PC. You should see a file with a name like
I906IXXU0AQD1_I906IOJV0AQD1_I906IXXU0AQD1_HOME.tar.md5. - Install Samsung USB drivers. If you haven’t already, install the drivers from Samsung’s website. This ensures your PC recognizes the phone in download mode.
- Enable USB debugging (optional but helpful). On the phone, go to Settings → About Phone → tap Build Number 7 times. Then go to Settings → Developer Options → enable USB Debugging.
- Power off the phone. Press and hold the power button, then tap Power Off. Wait for the screen to go completely black.
- Boot into Download Mode. Press and hold Volume Down + Home + Power simultaneously. When the warning screen appears, press Volume Up to continue. You should see a green Android icon and the text “Downloading…”
- Connect the phone to the PC. Plug the USB cable into the phone and then into the PC. Windows may install drivers for a few seconds.
- Open Odin. Right-click the Odin executable and select “Run as administrator”. The Odin window will open. You should see a blue or yellow box in the top-left corner labeled “ID:COM” indicating the phone is detected. If not, reinstall drivers or try a different USB port.
- Load the firmware into Odin. In Odin, click the “AP” button (or “PDA” in older versions). Navigate to the folder where you extracted the firmware and select the
.tar.md5file. Odin will verify the file; this can take a few minutes. - Verify Odin settings. Make sure only “F. Reset Time” and “Auto Reboot” are checked. Do NOT check “Re-Partition” – that can brick your phone. If the firmware package includes a PIT file, you may need it, but for standard stock firmware you don’t.
- Start the flash. Click the “Start” button. The progress bar in Odin will move. The phone will reboot automatically when done. You’ll see a green “PASS” message in Odin.
- Wait for the phone to boot. The first boot after flashing takes longer than normal (up to 10 minutes). Don’t touch the phone until it reaches the home screen.
- Check root status. Once booted, install a root checker app from the Play Store (like “Root Checker”) and run it. It should say “Root access is not properly installed” or similar.
Common Mistakes
- Wrong firmware. Using firmware for a different model (e.g., GT-I9060 instead of GT-I9060I) can cause a brick. Always verify the exact model number in Settings → About Phone before flashing.
- Re-Partition checked. This is the #1 cause of bricks. Unless you’re using a PIT file that came with the firmware, leave it unchecked.
- Interrupting the flash. Unplugging the cable or closing Odin mid-flash can permanently damage the phone. Be patient.
- Using a USB hub. Always connect directly to a USB port on the motherboard. Hubs can cause connection drops.
- Low battery. If the phone dies during flashing, it can be extremely difficult to recover. Charge to at least 50% before starting.
Tips
- Use the original Samsung cable – cheap third-party cables often have poor data transfer and can cause failures.
- Close all other programs on your PC during flashing to avoid CPU spikes that might interfere.
- If Odin doesn’t detect the phone, try a different USB port (preferably USB 2.0) and reinstall the Samsung USB drivers.
- After flashing, if the phone gets stuck in a boot loop, perform a factory reset from recovery mode (Volume Up + Home + Power).
- Keep a copy of the firmware file on your PC for future use – you may need it again if you decide to root later.
Troubleshooting
- Odin says “FAIL” or “There is no PIT partition”. This usually means the firmware doesn’t match the device. Re-download the correct firmware for GT-I9060I. If you have a PIT file, load it into the PIT section and check Re-Partition (only then).
- Phone stuck on Samsung logo after flash. This is often a cache issue. Boot into recovery (Volume Up + Home + Power) and select “wipe cache partition” and “wipe data/factory reset”. Then reboot.
- Odin doesn’t show the phone. Reinstall USB drivers, try a different cable, and ensure the phone is in Download Mode (green Android icon). If still not detected, try a different PC.
- Phone boots but root is still there. This can happen if you flashed a firmware that was pre-rooted. Download a completely stock, official firmware and repeat the process.
- Phone won’t enter Download Mode. Try holding Volume Down + Home + Power for 10 seconds. If that fails, remove the battery for 30 seconds, then try again.
Frequently Asked Questions
Will unrooting void my warranty?
Yes, the warranty is void as soon as you root. Flashing stock firmware may restore the software state, but Samsung’s service center can still detect that the flash counter was tripped (if you used a custom recovery).
Do I need to unlock the bootloader first?
No. The Galaxy Grand Neo Plus does not have a locked bootloader in the same way as newer Samsung devices. You can flash stock firmware directly with Odin.
Will I lose my apps and data?
Yes, flashing stock firmware wipes the data partition. Back up everything important before you start.
Can I unroot without a PC?
If you only want to remove root access (not restore the stock ROM), you can use an app like SuperSU’s “Full unroot” option. However, this may not be reliable and won’t restore the stock recovery. The safest method is flashing via Odin.
What if I get a boot loop after flashing?
Boot into recovery mode and do a factory reset. If that doesn’t help, re-flash the firmware with Odin, making sure to use the correct file.
Is it safe to use any stock firmware for GT-I9060I?
No. Use firmware that matches your region (e.g., XME for Malaysia, INU for India). Using a different region’s firmware may cause network issues, but it won’t brick the phone. Check the model number carefully.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- Fix Error 0x8007025d in Windows 10
- Fix Alexa App Stuck on Setup
- Android Camera for 7 Office Tasks: Step-by-Step
- Pair Phone to Pioneer Stereo After Bluetooth Reset
- Fix Windows Not Saving Remote Desktop Credentials
- Essential Tips for macOS Users Switching to Windows