sodcalculator

10 Tech How-To

Can’t Install Windows 10? Here’s Why & Fixes

Guide 10-56752 · Updated · Step by step

If you can’t install Windows 10, the cause is almost always one of four things: insufficient disk space or incompatible hardware, a corrupted installation file or USB drive, a BIOS/UEFI setting that blocks booting from the installer, or an existing partition table that Windows Setup refuses to use. This guide walks through each cause in order of likelihood, with exact steps to identify and fix it.

Hardware Requirements: Is Your PC Actually Supported?

Windows 10 has specific minimum requirements, and if your machine falls short, Setup will either refuse to run or fail partway through. The official minimums are:

  • Processor: 1 GHz or faster with at least 2 cores (64-bit or 32-bit).
  • RAM: 2 GB for 64-bit, 1 GB for 32-bit.
  • Storage: 20 GB free for 64-bit, 16 GB for 32-bit.
  • Graphics: DirectX 9 or later with WDDM 1.0 driver.
  • Display: 800×600 resolution or higher.

If your PC is older than about 2010, check these first. A common failure is trying to install 64-bit Windows on a machine with only 2 GB of RAM and a 32-bit processor — that won’t work. Also note that Windows 10 version 22H2 (the last release) is the final version, and Microsoft ended support for it in October 2025, so while it still installs, it no longer receives security updates.

Disk Space and Partition Errors

Even if you have enough free space, Windows Setup can fail if the target drive has a problematic partition layout. The most frequent error is “We couldn’t create a new partition or locate an existing one”. This happens when:

  • The disk is using the wrong partition table (MBR vs. GPT) for your firmware.
  • The disk has more than 4 primary partitions (MBR limit).
  • There is a hidden system partition that blocks Setup.
  • The drive is dynamic, not basic.

Fix: During installation, when you reach the partition screen, delete all partitions on the target drive (if you don’t need the data), then click New to let Windows create the correct layout. If the drive still fails, you may need to clean it using DiskPart:

  1. At the Setup screen, press Shift+F10 to open Command Prompt.
  2. Type diskpart and press Enter.
  3. Type list disk to identify your target disk (usually Disk 0).
  4. Type select disk 0 (replace 0 with your disk number).
  5. Type clean to wipe the disk completely.
  6. Type exit and close Command Prompt, then refresh the partition screen.

Caution: This erases everything on that disk. Double-check you selected the right one.

BIOS/UEFI Settings That Block Installation

Modern PCs use UEFI firmware, and Windows 10 expects to boot in UEFI mode with Secure Boot enabled. If your BIOS is set to Legacy (CSM) mode, Setup may fail with an error like “Windows cannot be installed to this disk. The selected disk is of the GPT partition style” or it may not even see your USB drive.

Check these settings in BIOS/UEFI:

  • Boot Mode: Set to UEFI (not Legacy or CSM). If you have a very old PC that only supports Legacy, you’ll need to convert the disk to MBR, but UEFI is standard for Windows 10.
  • Secure Boot: Enable it (if your hardware supports it). Some custom-built PCs have it disabled by default.
  • TPM: Not required for Windows 10 (only Windows 11), but if your motherboard has a TPM chip, make sure it’s enabled — some systems won’t boot the installer without it.
  • Fast Boot: Disable it, as it can prevent the USB from being recognized.

If you’re not sure how to enter BIOS, restart your PC and press the key shown on screen (often Del, F2, F12, or Esc). Look for a “Boot” or “Startup” tab.

Corrupted Installation Media

A bad USB drive or a corrupted ISO file is a classic cause. Symptoms include Setup freezing at a certain percentage, or errors like “Windows cannot install required files”.

Fix: Recreate your installation media using Microsoft’s official tool. Download the Media Creation Tool from Microsoft’s website (search “Download Windows 10”). Run it and choose “Create installation media for another PC”. Use a USB drive that’s at least 8 GB and has no other important files on it. If you’re using an ISO to burn a DVD, try a different burning program or a different disc.

Also, if you’re installing from a USB 3.0 port and it fails, try a USB 2.0 port — some older systems have driver issues with USB 3.0 during Setup.

Driver and Incompatibility Issues

Windows Setup needs to load drivers for your storage controller (especially NVMe SSDs or RAID arrays). If it can’t see your hard drive at all, it’s usually a missing driver. You’ll see a blank list when asked where to install Windows.

Fix: Download the storage driver (e.g., Intel Rapid Storage Technology or NVMe driver) from your motherboard or laptop manufacturer’s website. Extract it to a folder on a USB drive. In Setup, click Load Driver and browse to that folder. This is a common issue on newer laptops with Intel 11th-gen or later CPUs, where the VMD (Volume Management Device) controller is enabled by default. You can either disable VMD in BIOS (if allowed) or load the Intel RST driver.

Frequently Asked Questions

Why does Windows 10 installation fail with “0x80070070”?

This error means there isn’t enough disk space. Free up space on the target drive, or use a larger drive. If you’re upgrading from an older Windows, run Disk Cleanup first.

Can I install Windows 10 on a PC with only 1 GB of RAM?

Technically yes for 32-bit, but it will be extremely slow and may fail during installation due to memory pressure. Microsoft recommends 2 GB minimum even for 32-bit. It’s not a good idea; consider a lightweight Linux distribution instead.

Why does my USB drive not show up in boot menu?

Either the USB isn’t bootable (you didn’t create it correctly), or your BIOS is set to Legacy mode while the USB is UEFI-only, or vice versa. Recreate the USB with the Media Creation Tool and check your boot mode.

Can I install Windows 10 without a product key?

Yes. During installation, when asked for a key, click “I don’t have a product key”. Windows will install and run in an unactivated state, with limited personalization options, but fully functional. You can enter a key later in Settings.

What should I do if installation freezes at “Getting files ready for installation”?

This often indicates a hardware issue, especially RAM or hard drive. Try removing any unnecessary hardware (extra RAM sticks, external drives), and run a memory test (Windows Memory Diagnostic). Also, ensure your power supply is adequate.

Is it worth installing Windows 10 in 2025?

Windows 10 reached end of support on October 14, 2025. That means no more security updates. If you have a PC that can’t run Windows 11, you can still install Windows 10, but you should be aware of the risks. For most people, upgrading to Windows 11 (if your hardware supports it) or switching to Linux is safer.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →