sodcalculator

10 Tech How-To

iPad Won’t Turn On? Fix a Dead Device

Guide 10-44225 · Updated · Step by step

If your iPad is completely unresponsive and won’t turn on, the fix is usually a forced restart, a proper charge, or a recovery mode restore. Start by plugging it into power for at least 30 minutes, then force restart it; if that fails, connect to a computer and restore via recovery mode.

Why an iPad Goes Completely Dead

An iPad that shows no sign of life—no Apple logo, no chime, no screen glow—typically has one of three underlying issues: a fully drained battery, a software crash that froze the system, or a hardware failure. The most common is a drained battery, especially if the device sat unused for weeks or was left in extreme cold. A software crash can also make the iPad appear dead because the screen stays black even though the system is technically powered on. Less common but possible are hardware faults like a damaged charging port, a failed display cable, or a logic board issue. Understanding which category your iPad falls into helps you choose the right fix without wasting time on unnecessary steps.

Step 1: Charge It Properly

Before assuming the worst, give the battery a chance. Use the original Apple USB-C or Lightning cable and a wall adapter—not a computer’s USB port, which may provide too little power. Plug it in and leave it for at least 30 minutes. If the battery was completely flat, the screen may stay black for a while before showing a charging icon. If you see a red battery icon or a lightning bolt, the iPad is charging and will eventually turn on. If nothing appears after an hour, try a different cable and adapter, and inspect the charging port for lint or debris. A toothpick or soft brush can gently clear it, but avoid metal tools that could damage the pins.

Step 2: Force Restart (No Buttons? Still Works)

If charging doesn’t bring it back, a force restart often revives an iPad stuck in a black screen. The method depends on your model:

  • iPad with Face ID (iPad Pro 2018 and later, iPad Air 4th gen and later, iPad mini 6th gen): Press and quickly release the Volume Up button, then the Volume Down button, then press and hold the Top button until the Apple logo appears. This can take up to 30 seconds.
  • iPad with Home button (all other models): Press and hold both the Home button and the Top (or Side) button simultaneously. Keep holding until the Apple logo shows.

A force restart does not erase data—it’s a hard reset of the hardware. If the iPad responds, it will boot normally. If not, move to the next step.

Step 3: Recovery Mode and Restore

When a force restart fails, the iPad’s software may be corrupted. Recovery mode lets you reinstall the operating system while keeping your data (if possible) or erasing it as a last resort. You’ll need a computer with the latest version of Finder (macOS Catalina or later) or iTunes (Windows or older macOS). Connect the iPad to the computer, then put it into recovery mode using the same button sequence as a force restart, but keep holding until you see the recovery mode screen—a computer icon with a cable. On the computer, a dialog will appear offering to Update or Restore. Choose Update first; it attempts to reinstall iOS without erasing your data. If Update fails or the iPad still won’t boot, you’ll need to Restore, which wipes the device and installs a fresh copy of iOS. After a restore, you can set up as new or restore from a backup.

Common Problems and Misconceptions

Many people assume a dead iPad is bricked forever, but that’s rarely true. A common misconception is that holding the power button longer will fix it—it won’t; the force restart sequence is specific. Another is that a dead battery needs a “jump start” from a computer—actually, a wall adapter delivers more power. If your iPad shows the Apple logo but then goes black, that usually points to a software issue that recovery mode can fix. If recovery mode itself fails or the iPad repeatedly crashes, the problem may be hardware, such as a failing battery or a loose display connector. In that case, professional repair is the next step.

When to Seek Professional Repair

If you’ve tried charging, force restarting, and recovery mode without success, the iPad likely has a hardware fault. Common culprits include a swollen battery (which can push the screen outward), a damaged charging port, or a failed logic board. Apple and authorized service providers can diagnose the issue. If your iPad is under warranty or AppleCare+, repairs may be covered. Out-of-warranty costs vary, but a battery replacement is often cheaper than a new iPad. Avoid opening the device yourself unless you have experience—it can void any remaining warranty and risk further damage.

Preventing Future Dead-Device Issues

Once your iPad is working again, take steps to avoid a repeat. Keep the battery charged between 20% and 80% for longevity, but don’t obsess—modern batteries handle full cycles well. Update iOS regularly to fix software bugs that can cause crashes. If you store the iPad for a long time, charge it to about 50% and power it off. Avoid extreme temperatures, as heat can damage the battery and cold can cause sudden shutdowns. Finally, back up regularly via iCloud or a computer so that even a worst-case restore won’t lose your photos, messages, and apps.

Frequently Asked Questions

How long should I charge a dead iPad before trying to turn it on?

Charge for at least 30 minutes with a wall adapter. If the battery is completely drained, it may take up to an hour before the iPad responds. If you see a charging icon, it’s working—just wait longer.

Will a force restart delete my data?

No, a force restart is safe and does not erase any data. It only interrupts the current power state and forces the hardware to reboot, similar to unplugging and replugging a desktop computer.

What if recovery mode doesn’t work?

If recovery mode fails or the iPad won’t enter it, try a different cable and USB port, and ensure your computer’s software is up to date. If it still fails, the issue is likely hardware, and you should contact Apple Support or a repair shop.

Can I fix a water-damaged iPad myself?

Water damage is tricky. If your iPad got wet, turn it off immediately, dry it with a soft cloth, and place it in a dry area with airflow. Do not use rice—it can leave residue. After 48 hours, try charging and force restarting. If it doesn’t work, professional repair is your best bet, as corrosion can spread.

Why does my iPad turn on but the screen stays black?

This often indicates a display connection issue or a software crash. Try a force restart first. If that doesn’t help, connect to a computer and attempt recovery mode. If the iPad is recognized but the screen stays black, the display cable may be loose or damaged, requiring repair.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →