If your iPhone won’t charge, the fix is usually simple: check the port for lint, try a different cable and power adapter, force restart the phone, and clean the charging contacts. This guide walks through the most common causes and the exact steps to get your iPhone charging again, from quick checks to deeper software and hardware fixes.
Why Your iPhone Stops Charging
An iPhone that refuses to charge usually has one of four problems: a blocked or damaged charging port, a faulty cable or adapter, a software glitch that stops the charging process, or a battery that has reached the end of its life. Less common causes include a bent charging pin on the cable, water or corrosion inside the port, or a third-party accessory that isn’t MFi-certified. Understanding which category your issue falls into helps you pick the right fix without wasting time.
Quick Checks Before You Panic
Start with the simplest possibilities, because they account for a surprising number of “won’t charge” cases.
- Try a different outlet. Wall outlets can be dead or have a tripped GFCI. Plug your charger into another outlet or a known-working USB port on a computer.
- Swap the cable. Lightning and USB-C cables fray internally even when they look fine. Borrow a friend’s cable or use a new one.
- Swap the power adapter. The adapter itself can fail. Try a different one, ideally with the same or higher wattage.
- Check the charging port. Shine a flashlight inside. If you see lint, dust, or debris, it’s blocking the connection.
- Restart your iPhone. A simple restart clears many temporary software glitches that can interrupt charging.
Clean the Charging Port (The Most Common Fix)
Pocket lint and dust pack into the Lightning or USB-C port over time, preventing the connector from seating fully. This is the most frequent reason an iPhone stops charging, especially if the cable only works when you wiggle it or press down.
- Turn off your iPhone and unplug any cable.
- Use a wooden toothpick, a plastic dental floss pick, or a soft anti-static brush. Do not use metal (paperclips, needles, SIM ejector tools) — they can short-circuit pins or scratch the port walls.
- Gently scrape the bottom of the port and the sides, sweeping debris out. Avoid poking deep or with force.
- Use compressed air (short bursts) to blow out loosened particles. Hold the can upright to avoid moisture.
- Wait a few seconds, then try charging again.
If the port looks corroded or has green/white residue, that’s water damage — skip cleaning and see the safety section below.
Force Restart to Clear Charging Glitches
Sometimes the iPhone’s power management software gets stuck, and it won’t accept a charge even though the hardware is fine. A force restart is different from a normal restart and often fixes this.
- iPhone 8 or later (including SE 2nd gen and newer): Press and quickly release Volume Up, then Volume Down, then press and hold the Side button until the Apple logo appears (about 10 seconds).
- iPhone 7 / 7 Plus: Press and hold both the Side and Volume Down buttons for at least 10 seconds until the Apple logo appears.
- iPhone 6s and earlier: Press and hold both the Home and Side (or Top) buttons for at least 10 seconds.
After the logo appears, plug in your charger. In many cases, the phone will start charging normally.
Check for Water or Corrosion Damage
Modern iPhones are water-resistant, but that doesn’t mean the charging port is immune to moisture. If you’ve recently been near water, sweat, or high humidity, the port may detect liquid and disable charging to prevent damage. You’ll often see a warning on the screen: “Liquid detected in Lightning Connector.”
- Unplug everything and dry the iPhone with a soft cloth.
- Tap the phone gently against your hand, port facing down, to shake out liquid.
- Leave it in a dry, well-ventilated area for a few hours. A fan can help. Do not use rice or heat — rice dust can get into the port, and heat can damage the battery.
- Try charging again after several hours. If the warning persists, the port may have corrosion that needs professional cleaning.
Software Settings and Battery Health
If the hardware seems fine but the phone still won’t charge, check these software-related items.
- Battery Health: Go to Settings > Battery > Battery Health & Charging. If it says “Service” or the maximum capacity is below 80%, the battery may be degraded. A severely degraded battery can fail to charge or cause the phone to shut down even when plugged in.
- Optimized Battery Charging: This feature (on by default) delays charging past 80% until you need it. If your phone is plugged in overnight, it may stay at 80% for hours — that’s normal, not a fault.
- iOS Update: Go to Settings > General > Software Update and install any pending updates. Charging bugs have been fixed in iOS updates before.
- Reset All Settings: If nothing else works, go to Settings > General > Transfer or Reset iPhone > Reset > Reset All Settings. This won’t erase your data but will reset Wi-Fi, Bluetooth, and other system settings that might be interfering.
When to Seek Professional Repair
If you’ve cleaned the port, tried multiple cables and adapters, force restarted, and still get no charge, the problem is likely hardware. Common culprits include a broken charging port (often from a drop), a damaged charging IC on the logic board, or a dead battery. At this point, contact Apple Support or visit an Apple Store or authorized service provider. They can run diagnostics and replace the battery or repair the port. Avoid opening the iPhone yourself — it’s difficult and can cause more damage.
Frequently Asked Questions
Why does my iPhone only charge when the cable is held a certain way?
That’s almost always a worn cable or a dirty port. The connector isn’t making full contact. Try a new cable first; if that doesn’t help, clean the port as described above. If the issue persists, the port’s internal pins may be bent or broken, which requires repair.
Can I charge my iPhone wirelessly if the port is broken?
Yes, if your iPhone supports wireless charging (iPhone 8 and later), you can use a Qi-certified wireless charger. It won’t fix the port, but it will keep your phone powered while you arrange a repair. Note that wireless charging is slower than wired and generates more heat.
Is it safe to use a third-party charger?
Yes, as long as it’s MFi-certified (Made for iPhone) for Lightning cables, or USB-C with proper power delivery. Non-certified accessories may not charge reliably and can damage your battery or port over time. Look for the MFi logo on the packaging.
Why does my iPhone say “Liquid detected” when it hasn’t been near water?
Humidity, sweat, or condensation can trigger the sensor. The phone is protecting itself. Dry it thoroughly and wait a few hours. If the warning stays, the port may have corrosion, which needs professional cleaning.
How long should an iPhone battery last?
Apple estimates that a normal battery is designed to retain up to 80% of its original capacity at 500 complete charge cycles. That’s roughly two years of typical use. After that, you may notice shorter battery life and slower charging. You can check your cycle count in Settings > Battery > Battery Health on iOS 17.4 or later.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- iOS 18 Safari Not Working? Fixes That Help
- How to Check Your Linux Kernel for Spectre
- iPhone Safe Mode: How to Enable or Disable It
- Fix Slow Internet Lag on Samsung Galaxy Note
- How to Get iOS 17 on iPhone X (Safe Methods)
- Fix Gmail IMAP Error in Outlook: Step-by-Step