sodcalculator

10 Tech How-To

Window Well Covers: Best Options & How to Choose

Guide 10-51103 · Updated · Step by step

Window well covers protect basement windows from water, debris, animals, and falls while letting in light. This guide explains the main cover types, how to pick the right one for your window well, and what to watch for during installation. You will learn the pros and cons of polycarbonate, metal, and mesh covers, plus how to measure and secure them properly.

Why Window Wells Need Covers

A window well is the excavated area around a below-grade basement window. Without a cover, it collects leaves, snow, and rainwater, which can seep through the window frame or the well drain. Covers also keep out rodents, frogs, and insects, and they prevent people—especially children—from falling into an open well. The cover must still let light through, since basement windows are often the only natural light source for that room.

Building codes in many areas require covers on window wells deeper than a certain amount, typically 12–18 inches below grade, because they are a fall hazard. Check your local code before choosing a cover, as some jurisdictions specify minimum load ratings or material types.

Main Cover Types

There are three common materials, each with distinct trade-offs.

  • Polycarbonate (plastic) covers: The most popular choice. They are clear, letting in maximum light, and are very strong for their weight. A typical 1/4-inch thick polycarbonate sheet can support a person’s weight if properly framed. They resist UV degradation for many years but can yellow or scratch over time. They are the easiest to cut and install yourself.
  • Metal covers (steel or aluminum): Usually powder-coated black or dark gray. They are extremely durable and can support heavy snow loads, but they block most light. Steel rusts if the coating is scratched; aluminum does not rust but dents more easily. These are heavier and typically need a hinged frame for access.
  • Mesh or wire covers: Made of galvanized steel wire or plastic mesh. They let in the most light and air but do not keep out water or small debris. They are mainly for fall protection, not weatherproofing. Often used in mild climates or where the well has a good drain.

There are also hybrid covers: a metal frame with a polycarbonate insert, or a flat polycarbonate sheet with a metal grate on top for extra strength. These are less common and usually custom-made.

How to Choose the Right Cover

Match the cover to your climate, the well’s size, and how you use the window.

  • Snow load: In areas with heavy snow, choose a cover rated for the expected snow weight. Polycarbonate covers with a center support bar are usually sufficient. Metal covers are better for extreme snow regions.
  • Light needs: If the basement room is a bedroom or living space, pick clear polycarbonate. If the window is in a utility room, a metal cover is fine.
  • Access: If you need to open the window for ventilation or emergency egress, buy a hinged cover or one that lifts off easily. Many polycarbonate covers are held by four screws and can be removed in a minute. Metal covers often have a gas-strut hinge.
  • Well shape: Standard wells are rectangular. Round or custom-shaped wells need a custom cover, which costs more. Measure the outside rim dimensions, not the inside, and add 2 inches per side for overlap.

For a typical residential window well (about 36–48 inches long, 24–36 inches wide), a 1/4-inch thick clear polycarbonate cover with an aluminum frame is the most common and practical choice. It costs more than a plain sheet but resists sagging and cracking better.

Installation and Common Mistakes

Most covers mount to the house wall on one side and to the well rim on the other. The house side uses masonry anchors or screws into the foundation; the well side uses clips or screws into the metal or plastic well wall. The cover should sit slightly above the well rim so water runs off, not into the well.

Common mistakes include:

  • Measuring the inside of the well: This gives a cover that is too small and falls in. Always measure the outer lip.
  • Not sealing the house side: Gaps between the cover and the foundation let water run down the wall. Use a bead of exterior caulk along the top edge where the cover meets the house.
  • Using a cover that blocks egress: If the window is a required emergency exit, the cover must open from the inside without tools. Check your local fire code; some areas require a specific opening force.
  • Forgetting the drain: A cover keeps out rain, but condensation and melting snow still get in. Ensure the well’s gravel drain is clear before installing a cover.

Costs and Lifespan

Prices vary widely by size and material. A small polycarbonate cover for a 30×20-inch well can be under $50; a large custom metal cover for a 60×40-inch well can exceed $300. On average, expect to pay $100–$200 for a quality polycarbonate cover with a frame. Metal covers are usually 50–100% more expensive.

Lifespan depends on material. Polycarbonate lasts 10–20 years before yellowing or cracking from UV exposure. Metal covers last 20+ years if the coating is maintained. Mesh covers last 5–10 years before rusting. Replacing a cover is a simple DIY job; the main cost is the cover itself.

Safety and Code Considerations

The most important safety function is fall protection. A cover must support the weight of a person stepping on it, typically 250–300 pounds. Polycarbonate covers with a center support bar meet this; thin sheets (less than 1/8 inch) do not. If you are unsure, choose a cover with a metal frame or a metal grate on top.

For emergency egress, the cover must be openable from inside. This usually means a hinged cover with a latch that a person can reach through the window. Some covers have a quick-release mechanism. If your window is a bedroom egress, verify that the cover does not reduce the clear opening size required by code.

Never install a cover that is fully sealed and cannot be removed. You need access to clean the well, replace the window, or escape in an emergency. Also, keep the cover clear of leaves and snow in winter so it does not become an ice hazard.

Frequently Asked Questions

How do I measure my window well for a cover?
Measure the outside edge of the well rim, both length and width. Add 2 inches to each dimension for the overlap. For example, a well that is 38 inches long and 28 inches wide needs a cover about 40×30 inches. Round up to the nearest standard size.

Can I use a plain sheet of plexiglass as a cover?
Yes, but it is not recommended. Plexiglass (acrylic) is weaker than polycarbonate, cracks under impact, and degrades faster in sunlight. A 1/4-inch polycarbonate sheet is safer and lasts longer. If you use a plain sheet, drill holes for screws and add a center support bar to prevent sagging.

Do window well covers need to be vented?
No, but some covers have small vents to allow air circulation and reduce condensation. If the window is opened, a solid cover blocks airflow. A mesh cover or a cover with a vent is better if you rely on the window for ventilation. Condensation under a solid cover is normal; ensure the well drain is clear.

Will a cover keep water out completely?
No cover is completely waterproof. Heavy rain driven by wind can get under the edges. The cover’s job is to stop the majority of water and debris. The well’s gravel drain and the window’s own seal handle the rest. Install the cover with a slight tilt away from the house so water runs off the front edge.

How do I attach a cover to a metal window well?
Use self-tapping sheet metal screws or metal clips that grip the well rim. For the house side, use masonry screws into the foundation. Do not rely on adhesive alone; it will fail in cold weather. Pre-drill holes in the cover to avoid cracking the polycarbonate.

What is the best cover for a deep window well?
For wells deeper than 24 inches, choose a cover with a center support bar or a metal frame. Deep wells are more likely to be stepped on and collect more snow. A hinged metal cover with a gas strut is easiest to open for cleaning. For very deep wells, check local codes for specific load requirements.

Related

General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.

More in this bed

The whole Tech How-To bed →