This guide walks you through cloning your existing M.2 SATA SSD to a new M.2 NVMe SSD on a Windows PC. Cloning copies your entire Windows installation, programs, and files to the new drive, so you can upgrade to faster NVMe speeds without reinstalling Windows. You’ll need a free cloning tool, a spare M.2 slot or an external M.2 enclosure, and about 30–60 minutes.
What You’ll Need
- A Windows PC with an available M.2 slot (or a USB M.2 NVMe enclosure/adapter).
- The new M.2 NVMe SSD (must be at least as large as the used space on your current drive).
- A free cloning tool like Macrium Reflect Free, Clonezilla, or Samsung Data Migration (if the new drive is Samsung).
- A screwdriver (usually Phillips #0) to secure the M.2 drive.
- Optional: a USB drive to create a bootable rescue disk if your cloning software requires it.
Step-by-Step
- Back up important data. Before any disk operation, back up critical files to an external drive or cloud. Cloning is safe, but power loss or errors can cause data loss.
- Install the new NVMe SSD. Shut down your PC, unplug the power cable, and open the case. Insert the NVMe drive into a free M.2 slot (or use an external enclosure via USB). Secure it with the screw. Close the case and power on.
- Initialize the new drive (if needed). Open Disk Management (right-click Start → Disk Management). If the new drive shows as “Unknown” or “Not Initialized,” right-click it and choose “Initialize Disk.” Select GPT (recommended for UEFI systems) and click OK. Do not create any volumes yet.
- Download and install a cloning tool. For this guide, we’ll use Macrium Reflect Free (widely used and reliable). Install it and open the application.
- Select your source disk. In Macrium Reflect, you’ll see a list of disks. Identify your current M.2 SATA SSD (check the capacity and model). Click on it to select it, then click “Clone this disk” from the left panel.
- Choose the destination disk. In the clone wizard, click “Select a disk to clone to…” and choose your new NVMe SSD. Confirm it’s the correct drive – the software will show a warning if data will be overwritten.
- Adjust partitions (optional). If the new drive is larger, you can drag the partition boundaries to use the full space. If it’s the same size or smaller, leave as is. For most users, the default settings work fine.
- Start the clone. Click “Copy” (or “Next” in some versions). Review the summary, then click “Finish.” The clone will begin. This can take 10–60 minutes depending on the amount of data.
- Wait for completion. Do not use the computer for other tasks during cloning. When it finishes, you’ll see a message. Close Macrium Reflect.
- Shut down and remove the old drive. Power off your PC, unplug it, and remove the old M.2 SATA SSD. Leave the new NVMe drive in place. (You can keep the old drive as a backup, but for now, remove it to avoid boot confusion.)
- Boot from the new NVMe drive. Power on your PC. It should boot directly to Windows from the cloned NVMe drive. If it doesn’t, enter BIOS (usually Del or F2 during boot) and set the NVMe drive as the first boot option.
- Verify and extend the partition (if needed). Once Windows boots, open Disk Management. If the new drive is larger but the partition didn’t expand, right-click the C: partition and choose “Extend Volume” to use the unallocated space.
Common Mistakes
- Choosing the wrong source/destination. Double-check drive sizes and models. Cloning the wrong direction will wipe your new drive or your old data.
- Not initializing the new drive. Some cloning tools require the destination disk to be initialized first. If you skip this, the clone may fail.
- Cloning to a smaller drive. Your new NVMe must have at least as much capacity as the used space on your old drive. If it’s smaller, the clone will fail or be incomplete.
- Forgetting to change boot order. If you leave the old drive installed and boot order is wrong, Windows may still boot from the old drive.
- Using a SATA-only enclosure for an NVMe drive. NVMe drives need an NVMe-compatible enclosure. A SATA enclosure won’t work.
Tips
- If your new NVMe is a Samsung, use Samsung Data Migration – it’s free and very straightforward.
- Before cloning, run a disk cleanup and uninstall large programs you don’t use to reduce clone time.
- Make a system restore point before starting, just in case.
- After cloning, update your NVMe driver from the manufacturer’s website for best performance.
- If you plan to keep the old drive as storage, wipe it after confirming the clone works, to avoid boot conflicts.
Troubleshooting
Clone fails with “source disk too large” or “destination too small.” This means the used space on your source exceeds the new drive’s capacity. Delete files or shrink the source partition, then retry.
PC doesn’t boot from the new NVMe. Check BIOS boot order. If the drive isn’t listed, ensure the M.2 slot supports NVMe (some slots are SATA-only). Also, try reseating the drive.
Windows boots but shows the old drive’s capacity. You need to extend the partition in Disk Management. Right-click the C: partition → Extend Volume.
Cloning software doesn’t see the new NVMe. Make sure the drive is properly seated and recognized in Disk Management. If using an external enclosure, try a different USB port or cable.
Boot error “No bootable device.” This often happens if the old drive is removed but the bootloader wasn’t cloned correctly. Reconnect the old drive, boot into Windows, and run the cloning tool again, ensuring you clone all partitions (including the EFI system partition).
Frequently Asked Questions
Q: Can I clone from a larger SATA SSD to a smaller NVMe SSD?
A: Only if the used space on the source is smaller than the destination’s capacity. The clone tool copies only used sectors, so if you have 200GB used and the new drive is 250GB, it works.
Q: Do I need to reinstall Windows after cloning?
A: No, that’s the point of cloning. Your new NVMe will boot exactly as your old drive did.
Q: Will cloning void my Windows license?
A: No. Cloning to a new drive is fine. If Windows asks for activation, use the “I changed hardware” option and sign in with your Microsoft account.
Q: Can I clone to an external NVMe drive via USB?
A: Yes, as long as you use an NVMe-compatible USB enclosure. The clone will work, but you’ll need to install the NVMe internally afterward to boot from it.
Q: What if my new NVMe is not recognized in BIOS?
A: Check if your motherboard’s M.2 slot supports NVMe. Some older boards only support SATA M.2. Also, update your BIOS to the latest version.
Q: Is it better to do a fresh install instead of cloning?
A: Fresh installs avoid any driver conflicts or junk files, but cloning is faster and keeps all your settings. For most users, cloning works fine.
Related
General steps for current mainstream versions; menus can differ by device and version. See the disclaimer or report an error.
More in this bed
- How to Create App Shortcuts in Windows 10 Start Menu
- How to Rename a SQL Server Database
- Fix Google Calendar Not Syncing on iPhone
- Fix Skype Microphone Not Working on Windows
- Google Docs Landscape: Change Page Orientation
- Recover Deleted Admin Account in Windows 11